ARM ARM1176JZF-S Technical Reference Manual Download Page 717

Page: 717 / 759

Signal Descriptions

ARM DDI 0301H

A-7

ID012310

Non-Confidential, Unrestricted Access

A.5

AXI interface signals

The AXI interface ports operate using standard AXI signals, described in the following sections:

•

Instruction read port signals

•

Data port signals

on page A-8

•

Peripheral port signals

on page A-9

•

DMA port signals

on page A-10.

Note

•

All the outputs listed in this section have their reset values during Standby.

•

Full descriptions of the AXI interface signals are given in the

AMBA

AXI Protocol V1.0

Specification

. This section only summarizes how the AXI interfaces are implemented on

this processor.

The AXI signal names have a one or two-letter suffix that indicate the port, as shown in
Table A-5.

A.5.1

Instruction read port signals

The instruction read port is a 64-bit wide read-only AXI port. The standard AXI read channel
signal names are suffixed with

, and the implementation details of the port are:

•

ARID[3:0]

and

RID[3:0]

signals are not implemented

•

the read data bus is implemented as

RDATAI[63:0]

•

the

ARSIDEBANDI[4:0]

output is implemented to indicate shared and inner cacheable

accesses.

Table A-6 on page A-8 gives more information about the instruction read port AXI
implementation. See the AMBA

AXI Protocol V1.0 Specification for details of the other

signals on this port.

Table A-5 Port signal name suffixes

Port

Suffix

Comment

Instruction fetch

Read-only

Data read/write

Read/write

Peripheral

Read/write

DMA

Read/write

Summary of Contents for ARM1176JZF-S























































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ARM1176JZF-S

Reviews:

Related manuals for ARM1176JZF-S

Brands by name

Popular brands

ARM ARM1176JZF-S, Technical Reference Manual

Search results

Summary of Contents for ARM1176JZF-S

Reviews:

Related manuals for ARM1176JZF-S

Brands by name

Popular brands