manualshive.com logo in svg

ARM ARM1176JZF-S, Technical Reference Manual

The ARM ARM1176JZF-S Technical Reference Manual is a comprehensive user manual for the ARM1176JZF-S processor. Download this manual for free from manualshive.com, to gain valuable insights into the product's technical specifications, performance, and programming details. Enhance your understanding of this advanced processor with this detailed manual.

Share
Download
background image

Coprocessor Interface 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

11-8

ID012310

Non-Confidential, Unrestricted Access

The flushing mechanism is simplified because successive coprocessor instructions have 
contiguous tags. The core manages this by only incrementing the tag number when the 
instruction passed to the coprocessor is a coprocessor instruction. This is done after sending the 
instruction, so the tag changes after a coprocessor instruction is sent, rather than before. It is not 
possible to increment the tag before sending the instruction because the core has not yet had time 
to decode the instruction to determine what kind of instruction it is. When the coprocessor 
Decode stage removes the non-coprocessor instructions, it is left with an instruction stream 
carrying contiguous tags. The tags can also be used to verify that the sequence of tokens moving 
down the queues matches the sequence of instructions moving down the core and coprocessor 
pipelines.

11.2.6

Flush broadcast

If a branch has been mispredicted, it might be necessary for the core to flush both pipelines. 
Because this action potentially affects the entire pipeline, it is not passed across in a queue but 
is broadcast from the core to the coprocessor, subject to the same timing constraints as the 
queues. When the flush signal is received by the coprocessor, it causes the pipeline and the 
instruction queue to be cleared up to the instruction triggering the flush. This is explained in 
more detail in 

Flush operations

 on page 11-19.

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Panasonic WJ-NV200K Quick Reference Manual preview
WJ-NV200K
Brand: Panasonic Pages: 4
Harman Kardon CITATION 7.0 Owner'S Manual preview
CITATION 7.0
Brand: Harman Kardon Pages: 66
National Instruments NI 9213 Getting Started preview
NI 9213
Brand: National Instruments Pages: 11
TC-Helicon PERFORM-VK Quick Start Manual preview
PERFORM-VK
Brand: TC-Helicon Pages: 2
IDT TSI384 User Manual preview
TSI384
Brand: IDT Pages: 281
DMX4ALL DMX-Universal-Demux User Manual preview
DMX-Universal-Demux
Brand: DMX4ALL Pages: 17
Rockwell Automation 41LR4060 Instruction Manual preview
41LR4060
Brand: Rockwell Automation Pages: 108
BSS Audio EC-4B Installation Manual preview
EC-4B
Brand: BSS Audio Pages: 20
Reeven NAIA Installation Manual preview
NAIA
Brand: Reeven Pages: 2
Alesis QUADRAVERB Service Manual preview
QUADRAVERB
Brand: Alesis Pages: 46
Cateye Urban Wireless CC-VT240W Instruction Manual preview
Urban Wireless CC-VT240W
Brand: Cateye Pages: 15
Internet Security Systems Proventia A1204 User Manual preview
Proventia A1204
Brand: Internet Security Systems Pages: 42
Hanwha Techwin Wisenet PRN-6400B4 Quick Manual preview
Wisenet PRN-6400B4
Brand: Hanwha Techwin Pages: 14
ZALMAN FS-V7 User Manual preview
FS-V7
Brand: ZALMAN Pages: 9
JETWAY HBJC924R3288DG2NS Series Quick Installation Manual preview
HBJC924R3288DG2NS Series
Brand: JETWAY Pages: 6
H3C LSWM12H2Q User Manual preview
LSWM12H2Q
Brand: H3C Pages: 9
Kentrox RMM-1400 Configuration Manual preview
RMM-1400
Brand: Kentrox Pages: 246
TRENDnet TEW-221PC User Manual preview
TEW-221PC
Brand: TRENDnet Pages: 56

Brands by name

Popular brands

Load more brands