manualshive.com logo in svg

ARM ARM1176JZF-S, Technical Reference Manual

The ARM ARM1176JZF-S Technical Reference Manual is a comprehensive user manual for the ARM1176JZF-S processor. Download this manual for free from manualshive.com, to gain valuable insights into the product's technical specifications, performance, and programming details. Enhance your understanding of this advanced processor with this detailed manual.

Share
Download
background image

System Control Coprocessor 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-73

ID012310

Non-Confidential, Unrestricted Access

The value of S is given by:

See 

c0, Cache Type Register

 on page 3-21 for details of instruction and data cache 

size.

Note

 

If the data is stated to be Set and Index format, see Figure 3-40 on page 3-72, it 
identifies the cache line that the operation applies to by specifying the cache Set 
that it belongs to and what its Index is within the Set. The Set corresponds to the 
number of the cache way, and the Index number corresponds to the line number 
within a cache way.

MVA format 

Figure 3-41 shows the MVA format for invalidate, clean, and prefetch operations.

Figure 3-41 c7 format for MVA

Table 3-69 lists how the bit values correspond with the Cache Operation functions 
for MVA format operations.

Note

 

•

Invalidation and cleaning operations have no effect if they miss in the 
cache. 

•

If the corresponding entry is not in the TLB, these instructions can cause a 
TLB miss exception or hardware page table walk, depending on the miss 
handling mechanism.

•

For the cache control operations, the MVAs that are passed to the cache are 
not translated by the FCSE extension.

VA format 

Figure 3-42 shows the VA format for invalidate and clean operations. All VA 
format operations use the MCRR instruction.

Figure 3-42 Format of c7 for VA

Associativity x line length in bytes

cache size

S = log

2

Modified virtual address

31

5 4

0

SBZ

Table 3-69 Functional bits of c7 for MVA

Bits

Field name

Function

[31:5]

MVA

Specifies address to invalidate, clean, or prefetch.

Holds the MVA of the cache line.

[4:0]

-

Ignored. This means that the lower 5 bits of MVA are ignored and these bits are not used for the 
cache operations. Only the top bits are necessary to determine whether or not the cache line is 
present in the cache. Even if the MVA is not aligned to the cache line, the cache operation is 
performed by ignoring the lower 5 bits.

Virtual address

31

4

0

SBZ

5

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Panasonic WJ-NV200K Quick Reference Manual preview
WJ-NV200K
Brand: Panasonic Pages: 4
Freescale Semiconductor FRDM-STBC-SA9500 Quick Reference Card preview
FRDM-STBC-SA9500
Brand: Freescale Semiconductor Pages: 2
Lanner electronics EM-566 Series Manual preview
EM-566 Series
Brand: Lanner electronics Pages: 59
Cytron Technologies SHIELD-2AMOTOR User Manual preview
SHIELD-2AMOTOR
Brand: Cytron Technologies Pages: 13
JETWAY I848ASR1A User Manual preview
I848ASR1A
Brand: JETWAY Pages: 47
OPTO 22 PCI-AC48 User Manual preview
PCI-AC48
Brand: OPTO 22 Pages: 28
Keil RTX51 Manual preview
RTX51
Brand: Keil Pages: 68
AXIOMTEK FAB118-14B5P7 Quick Installation Manual preview
FAB118-14B5P7
Brand: AXIOMTEK Pages: 2
Teridian 71M6533 Quick Start Manual preview
71M6533
Brand: Teridian Pages: 2
RAID N8103-134 Setup Manual preview
N8103-134
Brand: RAID Pages: 80
Intel NetStructure ZT 5085 Manual preview
NetStructure ZT 5085
Brand: Intel Pages: 106
Roland Symphonique Strings SRX-04 Owner'S Manual preview
Symphonique Strings SRX-04
Brand: Roland Pages: 12
ICOP Technology Vortex86SX VSX-6101 User Manual preview
Vortex86SX VSX-6101
Brand: ICOP Technology Pages: 50
Alpine PXE-R600 Manual preview
PXE-R600
Brand: Alpine Pages: 17
Tvone CORIOview MWP Series Quick Start Manual preview
CORIOview MWP Series
Brand: Tvone Pages: 24
IBM 55PUS8118 SCSI-2 Installation Manual preview
55PUS8118 SCSI-2
Brand: IBM Pages: 42
Asus TeleSky User Manual preview
TeleSky
Brand: Asus Pages: 56
ProCurve 800 Configuration Manual preview
800
Brand: ProCurve Pages: 406

Brands by name

Popular brands

Load more brands