ARM ARM1176JZF-S Technical Reference Manual Download Page 30 | Manualshive

Page: 30 / 759

background image

Introduction

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

1-4

ID012310

Non-Confidential, Unrestricted Access

1.3

TrustZone security extensions

Caution

TrustZone security extensions enable a Secure software environment. The technology does not
protect the processor from hardware attacks and the implementor must take appropriate steps to
secure the hardware and protect trusted code.

The ARM1176JZF-S processor supports TrustZone security extensions to provide a secure
environment for software. This section summarizes processor elements that TrustZone uses. For
details of TrustZone, see the

ARM Architecture Reference Manual

.

The TrustZone approach to integrated system security depends on an established trusted code
base. The trusted code is a relatively small block that runs in the Secure world in the processor
and provides the foundation for security throughout the system. This security applies from
system boot and enforces a level of trust at each stage of a transaction.

The processor has:

•

seven operating modes that can be either Secure or Non-secure

•

Secure Monitor mode, that is always Secure.

Except when the processor is in Secure Monitor mode, the NS bit in the Secure Configuration
Register determines whether the processor runs code in the Secure or Non-secure worlds. The
Secure Configuration Register is in CP15 register c1, see

c1, Secure Configuration Register

on

page 3-52.

Secure Monitor mode is used to switch operation between the Secure and Non-secure worlds.

Secure Monitor mode uses these banked registers:

R13_mon

Stack Pointer

R14_mon

Link Register

SPSR_mon

Saved Program Status Register

The processor implements this instruction to enter Secure Monitor mode:

SMC

Secure Monitor Call, switches from one of the privileged modes to the Secure
Monitor mode.

The processor implements these TrustZone related signals:

nDMASIRQ

Secure DMA transfer request, see

c11, DMA Channel Status Register

on

page 3-117.

nDMAEXTERRIR

Not maskable error DMA interrupt, see

c11, DMA Channel Status Register

on

page 3-117.

SPIDEN

Secure privileged invasive debug enable, see

Secure Monitor mode and debug

on

page 13-4.

SPNIDEN

Secure privileged non-invasive debug enable, see

Secure Monitor mode and

debug

on page 13-4.

Note

Do not confuse Secure Monitor mode with the Monitor debug-mode.

«
...
28
29
30
31
32
...
»

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Brand: IBM Pages: 86

Brand: Lattice Semiconductor Pages: 15

iCE40 UltraLite

Brand: Lattice Semiconductor Pages: 13

Brand: YASKAWA Pages: 34

Brand: Paradox Pages: 4

S5120V3-EI Series

Brand: H3C Pages: 54

Brand: Ublox Pages: 116

Brand: Ubiquiti Pages: 23

Brand: Supero Pages: 53

Brand: Alcatel-Lucent Pages: 60

Brand: Adaptec Pages: 2

Brand: Costar Pages: 24

TV@nywhere Satellite

Brand: MSI Pages: 2

Brand: MSI Pages: 182

Brand: StarTech.com Pages: 20

Brand: Motorola Pages: 18

Brand: Motorola Pages: 19

Brand: Motorola Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands