manualshive.com logo in svg

ARM ARM1176JZF-S, Technical Reference Manual

The ARM ARM1176JZF-S Technical Reference Manual is a comprehensive user manual for the ARM1176JZF-S processor. Download this manual for free from manualshive.com, to gain valuable insights into the product's technical specifications, performance, and programming details. Enhance your understanding of this advanced processor with this detailed manual.

Share
Download
background image

Cycle Timings and Interlock Behavior 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

16-19

ID012310

Non-Confidential, Unrestricted Access

16.11 Load and Store Double instructions

This section describes the cycle timing behavior for the LDRD and STRD instructions

The LDRD and STRD instructions:

•

Are two-cycle issue if either a negative register offset or a shift other than LSL #2 is used. 
Only the offset register is an Early Reg.

•

Are single-cycle issue if either a constant offset is used or if a register offset with no shift, 
or shift by 2 is used. Both the base and any offset register are Early Regs.

•

Take only one memory cycle if the address is doubleword aligned.

•

Take two memory cycles if the address is not doubleword aligned.

The updated base register has a result latency of one. For back-to-back load/store instructions 
with base write back, the updated base is available to the following load/store instruction with a 
result latency of 0.

To prevent instructions after a STRD from writing to a register before it has stored that register, 
the STRD registers have a lock latency that determines how many cycles it is before a 
subsequent instruction that writes to that register can start.

Table 16-16 lists the cycle timing behavior for LDRD and STRD instructions.

Table 16-17 lists the explanation of 

<addr_md_1cycle>

 and 

<addr_md_2cycle>

 that Table 16-16 

uses.

Table 16-16 Load and Store Double instructions cycle timing behavior

Example instruction

Cycle
s

Memory cycles

Result latency 
(LDRD)

Register lock latency 
(STRD)

Address is double-word aligned

 

LDRD R1, <addr_md_1cycle>

a

1

1

3/3

1,2

LDRD R1, <addr_md_2cycle>

a

2

2

4/4

2,3

Address not double-word aligned 

LDRD R1, <addr_md_1cycle>

a

1

2

3/4

1,2

LDRD R1, <addr_md_2cycle>

a

2

3

4/5

2,3

a. Table 16-17 for an explanation of 

<addr_md_1cycle>

 and

 <addr_md_2cycle>

.

Table 16-17 <addr_md_1cycle> and <addr_md_2cycle> LDRD example instruction explanation

Example instruction

Early Reg

Comment

<addr_md_1cycle>

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Patton electronics 1084 Installation And Operation Manual preview
1084
Brand: Patton electronics Pages: 16
LSI MegaRAID SATA 300-4XLP Quick Installation Manual preview
MegaRAID SATA 300-4XLP
Brand: LSI Pages: 3
Buffalo LinkStation Mini User Manual preview
LinkStation Mini
Brand: Buffalo Pages: 71
ZALMAN CNPS7000C Series User Manual preview
CNPS7000C Series
Brand: ZALMAN Pages: 8
Eurotech Zypad WL15 Series Quick Start preview
Zypad WL15 Series
Brand: Eurotech Pages: 2
ICP DAS USA iWSN-200E Quick Start Manual preview
iWSN-200E
Brand: ICP DAS USA Pages: 8
Penguin Edge MVME2500 Quick Start Manual preview
MVME2500
Brand: Penguin Edge Pages: 2
Xyclop XC-4CH-NVR-1TB User Manual preview
XC-4CH-NVR-1TB
Brand: Xyclop Pages: 144
Silvertel Ag102 User Manual preview
Ag102
Brand: Silvertel Pages: 9
B&B Electronics 232PCC User Manual preview
232PCC
Brand: B&B Electronics Pages: 17
Hama 00176547 Operating Instruction preview
00176547
Brand: Hama Pages: 25
Stepper Motor Canada DB25-1205F Manual preview
DB25-1205F
Brand: Stepper Motor Canada Pages: 5
Amphenol C2LINX Series Installation Manual preview
C2LINX Series
Brand: Amphenol Pages: 43
Lanner ECA-4027 User Manual preview
ECA-4027
Brand: Lanner Pages: 99
Lanpro LP-F22 Series Assembling Instructions preview
LP-F22 Series
Brand: Lanpro Pages: 3
Lefroy Brooks M1-5100 Installation, Operating, & Maintenance Instructions preview
M1-5100
Brand: Lefroy Brooks Pages: 10
SIIG ExpressCard 11-in-1 Reader/Writer Quick Installation Manual preview
ExpressCard 11-in-1 Reader/Writer
Brand: SIIG Pages: 8
Quatech SSPX-100 User Manual preview
SSPX-100
Brand: Quatech Pages: 5

Brands by name

Popular brands

Load more brands