manualshive.com logo in svg

ARM ARM1176JZF-S, Technical Reference Manual

The ARM ARM1176JZF-S Technical Reference Manual is a comprehensive user manual for the ARM1176JZF-S processor. Download this manual for free from manualshive.com, to gain valuable insights into the product's technical specifications, performance, and programming details. Enhance your understanding of this advanced processor with this detailed manual.

Share
Download
background image

Debug Test Access Port 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

14-8

ID012310

Non-Confidential, Unrestricted Access

14.6

Debug registers

You can connect the following debug registers between 

DBGTDI

 and 

DBGTDO

:

•

Bypass register

•

Device ID code register

•

Instruction register

 on page 14-9

•

Scan chain select register (SCREG)

 on page 14-9

•

Scan chain 0, debug ID register (DIDR)

 on page 14-11

•

Scan chain 1, Debug Status and Control Register (DSCR)

 on page 14-11

•

Scan chain 4, instruction transfer register (ITR)

 on page 14-13

•

Scan chain 5

 on page 14-15.

•

Scan chain 6

 on page 14-17.

•

Scan chain 7

 on page 14-17.

14.6.1

Bypass register

Purpose 

Bypasses the device by providing a path between 

DBGTDI

 and 

DBGTDO

.

Length 

1 bit.

Operating mode 

When the bypass instruction is the current instruction in the instruction 
register, serial data is transferred from 

DBGTDI

 to 

DBGTDO

 in the 

Shift-DR state with a delay of one 

TCK

 cycle. There is no parallel output 

from the bypass register. A logic 0 is loaded from the parallel input of the 
bypass register in the Capture-DR state. Nothing happens at the 
Update-DR state.

Order 

Figure 14-3 shows the order of bits in the bypass register.

Figure 14-3 Bypass register bit order

14.6.2

Device ID code register

Purpose 

Device identification. To distinguish the ARM1176JZF-S processors from 
other processors, the DBGTAP controller ID is unique for each. This 
means that a DBGTAP debugger, such as RealView ICE, can easily see the 
processor that it is connected to. The Device ID register version and 
manufacturer ID fields are routed to the edge of the chip so that partners 
can create their own Device ID numbers by tying the pins to HIGH or 
LOW values.

The default manufacturer ID for the ARM1176JZF-S processor is 
b11110000111. The part number field is hard-wired inside the 
ARM1176JZF-S to 

0x7B76

.

0b0

DBGTDI

DBGTDO

Bypass

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

D-Link ShareCenter DNS-320L Datasheet preview
ShareCenter DNS-320L
Brand: D-Link Pages: 4
Paradyne 3163 Quick Reference preview
3163
Brand: Paradyne Pages: 16
Hama 39707 Operating Instruction preview
39707
Brand: Hama Pages: 4
Observint NVR4 Firmware User Manual preview
NVR4
Brand: Observint Pages: 117
Black Box JPM083A Manual preview
JPM083A
Brand: Black Box Pages: 9
Western Digital Scorpio WD2500BPVT Product Specifications preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 3
Western Digital Scorpio WD2500BPVT Product Features preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 4
Extron electronics PoleVault System A/V Source Inputs Specification Sheet preview
PoleVault System A/V Source Inputs
Brand: Extron electronics Pages: 4
Tandy 26-3814 Operation Manual preview
26-3814
Brand: Tandy Pages: 24
ZALMAN RESERATOR1 V2 Installation And Operational Manual preview
RESERATOR1 V2
Brand: ZALMAN Pages: 18
SeaLevel PC-ACB.MP User Manual preview
PC-ACB.MP
Brand: SeaLevel Pages: 21
VCS VIP 1000 User Manual preview
VIP 1000
Brand: VCS Pages: 118
Observint NVR16 Firmware User Manual preview
NVR16
Brand: Observint Pages: 117
PairGain PG-Flex FLC-704 Manual preview
PG-Flex FLC-704
Brand: PairGain Pages: 20
ETAS XETK-S22.0 User Manual preview
XETK-S22.0
Brand: ETAS Pages: 84
ActiveEye K9504L-W Operation Manual preview
K9504L-W
Brand: ActiveEye Pages: 35
DayTronic PC-HSICA Instruction Manual preview
PC-HSICA
Brand: DayTronic Pages: 13
Broadband Products Xtreme Networked Boat User Manual preview
Xtreme Networked Boat
Brand: Broadband Products Pages: 16

Brands by name

Popular brands

Load more brands