manualshive.com logo in svg

ARM ARM1176JZF-S, Technical Reference Manual

The ARM ARM1176JZF-S Technical Reference Manual is a comprehensive user manual for the ARM1176JZF-S processor. Download this manual for free from manualshive.com, to gain valuable insights into the product's technical specifications, performance, and programming details. Enhance your understanding of this advanced processor with this detailed manual.

Share
Download
background image

Unaligned and Mixed-endian Data Access Support 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

4-7

ID012310

Non-Confidential, Unrestricted Access

Figure 4-3 Store byte

4.3.4

Load unsigned halfword, little-endian

The addressed byte-pair is loaded from memory into the low 16 bits of the general-purpose 
register, and the upper 16 bits are zeroed so that the least-significant addressed byte in memory 
appears in bits [7:0] of the ARM register, as Figure 4-4 shows.

Figure 4-4 Load unsigned halfword, little-endian

If strict alignment fault checking is enabled and Address bit 0 is not zero, then a Data Abort is 
generated and the MMU returns a Misaligned fault in the Fault Status Register. 

4.3.5

Load unsigned halfword, big-endian

The addressed byte-pair is loaded from memory into the low 16 bits of the general-purpose 
register, and the upper 16 bits are zeroed so that the most-significant addressed byte in memory 
appears in bits [15:8] of the ARM register, as Figure 4-5 on page 4-8 shows.

Register

31

23

15

7

0

x

x

x

b

b

Memory

Address

A[31:0]

7

0

b1

b0

Memory

Register

31

23

15

7

0

Address

A[31:0]

7

0

0

0

b1

b0

+1

msbyte

lsbyte

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Mackie SP260 Installation Instructions preview
SP260
Brand: Mackie Pages: 2
Mackie SP260 Product Overview preview
SP260
Brand: Mackie Pages: 5
Patton electronics 1084 Installation And Operation Manual preview
1084
Brand: Patton electronics Pages: 16
ekwb EK-Vector Radeon RX5700 + XT Backplate Installation Manual preview
EK-Vector Radeon RX5700 + XT Backplate
Brand: ekwb Pages: 7
IBA ibaFOB-4i-X Manual preview
ibaFOB-4i-X
Brand: IBA Pages: 33
Renesas Emulator MCU Board for 38D5 Group M38D59T-RLFS User Manual preview
Emulator MCU Board for 38D5 Group M38D59T-RLFS
Brand: Renesas Pages: 4
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Brand: Buffalo Pages: 2
SSV Embedded Systems eSOM/3517 Hardware Reference Manual preview
eSOM/3517
Brand: SSV Embedded Systems Pages: 17
S&T TPMS1209T02-ER User Manual preview
TPMS1209T02-ER
Brand: S&T Pages: 28
ZALMAN CNPS 4X User Manual preview
CNPS 4X
Brand: ZALMAN Pages: 16
Bridgeworks Tamar FCSAS102800 User Manual preview
Tamar FCSAS102800
Brand: Bridgeworks Pages: 56
HMS Anybus AWB3000 Startup Manual preview
Anybus AWB3000
Brand: HMS Pages: 18
Intel SRCU31L Quick Start Manual preview
SRCU31L
Brand: Intel Pages: 20
BSS Audio Soundweb 9088ii DSP System    Brochure & Specs preview
Soundweb 9088ii DSP System   
Brand: BSS Audio Pages: 2
nox Hummer H-240CL Manual preview
Hummer H-240CL
Brand: nox Pages: 16
ZALMAN OPTIMA II CNPS10X User Manual preview
OPTIMA II CNPS10X
Brand: ZALMAN Pages: 20
WiebeTech FCDKV4 User Manual preview
FCDKV4
Brand: WiebeTech Pages: 8
Datavideo NVW-150 Instruction Manual preview
NVW-150
Brand: Datavideo Pages: 71

Brands by name

Popular brands

Load more brands