ARM ARM1176JZF-S Technical Reference Manual Download Page 134 | Manualshive

Page: 134 / 759

background image

System Control Coprocessor

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-2

ID012310

Non-Confidential, Unrestricted Access

3.1

About the system control coprocessor

The section gives an overall view of the system control coprocessor. For detail of the registers
in the system control coprocessor, see

System control processor registers

on page 3-13.

The purpose of the system control coprocessor, CP15, is to control and provide status
information for the functions implemented in the ARM1176JZF-S processor. The main
functions of the system control coprocessor are:

•

overall system control and configuration

•

cache configuration and management

•

Tightly-Coupled Memory

(TCM) configuration and management

•

Memory Management Unit

(MMU) configuration and management

•

DMA control

•

system performance monitoring.

The system control coprocessor does not exist in a distinct physical block of logic.

3.1.1

System control coprocessor functional groups

The system control coprocessor appears as a set of 32-bit registers that you can write to and read
from. Some of the registers permit more than one type of operation. The functional groups for
the registers are:

•

System control and configuration

on page 3-5

•

MMU control and configuration

on page 3-6

•

Cache control and configuration

on page 3-7

•

TCM control and configuration

on page 3-8

•

Cache Master Valid Registers

on page 3-8

•

DMA control

on page 3-9

•

System performance monitor

on page 3-10

•

System validation

on page 3-10.

The system control coprocessor controls the TrustZone operation of the processor:

•

some of the registers are only accessible in the Secure world

•

some of the registers are banked for Secure and Non-secure worlds

•

some of the registers are common to both worlds.

Note

When Secure Monitor mode is active the core is in the Secure world. The processor treats all
accesses as Secure and the system control coprocessor behaves as if it operates in the Secure
world regardless of the value of the NS bit, see

c1, Secure Configuration Register

on page 3-52.

In Secure Monitor mode, the NS bit defines the copies of the banked registers in the system
control coprocessor that the processor can access:

NS = 0

Access to Secure world CP15 registers

NS = 1

Access to Non-secure world CP15 registers.

Registers that are only accessible in the Secure world are always accessible in Secure Monitor
mode, regardless of the value of the NS bit.

Table 3-1 on page 3-3 lists the overall functionality for the system control coprocessor as it
relates to its registers.

«
...
132
133
134
135
136
...
»

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

ShareCenter DNS-320L

Brand: D-Link Pages: 4

DHI-NVR5224-24P-4KS2

Brand: Dahua Pages: 24

Brand: Telex Communications Pages: 28

Brand: Telit Wireless Solutions Pages: 113

Brand: EMCIS Pages: 14

500 - DATASHEET REV 003

Brand: Intel Pages: 67

Brand: NEC Pages: 70

Brand: Icy Box Pages: 2

POD-51EH-C541U-12

Brand: IceTech Pages: 8

Brand: Intel Pages: 154

Brand: PairGain Pages: 48

Cyclades CS4008

Brand: Avocent Pages: 2

Brand: Xaoc Devices Pages: 4

Brand: Alphacool Pages: 3

DM/V480A-2T1-PCI

Brand: Dialogic Pages: 2

POA-MD17SDID - Projector Terminal Expansion Board

Brand: Sanyo Pages: 4

Brand: SS Telecoms Pages: 35

ML370 - ProLiant - G3

Brand: Compaq Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands