manualshive.com logo in svg

ARM ARM1176JZF-S, Technical Reference Manual

The ARM ARM1176JZF-S Technical Reference Manual is a comprehensive user manual for the ARM1176JZF-S processor. Download this manual for free from manualshive.com, to gain valuable insights into the product's technical specifications, performance, and programming details. Enhance your understanding of this advanced processor with this detailed manual.

Share
Download
background image

Unaligned and Mixed-endian Data Access Support 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

4-19

ID012310

Non-Confidential, Unrestricted Access

Mixed-endian configuration supported

This behavior is enabled when the U bit in CP15 Register c1 is set. This is only supported when 
the B bit in CP15 Register c1 is reset, as Table 4-5 lists.

4.5.3

Reset values of the U, B, and EE bits

Table 4-6 lists the reset values of the 

BIGENDINIT

 and 

UBITINIT

 pins that determine the 

values of the U, B, and EE bits at reset. The pins determine the reset value of the B bit and both 
the Secure and Non-secure reset values of the U and EE bits.

Table 4-5 Mixed-endian configuration

U

B

E

Instruction 
endianness

Data 
endianness

Description

1

0

0

LE

LE

LE instructions, little-endian data load/store. Unaligned data access 
permitted.

1

0

1

LE

BE-8

LE instructions, big-endian data load/store. Unaligned data access 
permitted.

1

1

0

BE-32

BE-32

Legacy BE instructions/data.

1

1

1

-

-

Reserved.

Table 4-6 B bit, U bit, and EE bit settings

BIGENDINIT

UBITINIT

B

U

EE

0

0

0

0

0

0

1

0

1

0

1

0

1

0

0

1

1

0

1

1

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

IBM 3270 Operation Manual preview
3270
Brand: IBM Pages: 86
NEC N8104-213 Installation Manual preview
N8104-213
Brand: NEC Pages: 10
NEC N8104-213 Instructions Manual preview
N8104-213
Brand: NEC Pages: 8
IDT USB-BRIDGEV2-EVAL Evaluation Board Manual preview
USB-BRIDGEV2-EVAL
Brand: IDT Pages: 11
ATI Technologies Radeon Online Manual preview
Radeon
Brand: ATI Technologies Pages: 87
Noraxon TeleMyo 2400T V2 User Manual preview
TeleMyo 2400T V2
Brand: Noraxon Pages: 52
7th Sense Pixel Processing Juggler User Manual preview
Pixel Processing Juggler
Brand: 7th Sense Pages: 148
Acconeer XE132 Getting Started Manual preview
XE132
Brand: Acconeer Pages: 13
MSI TV@nywhere A/D User Manual preview
TV@nywhere A/D
Brand: MSI Pages: 44
MSI MS-98H2 Manual preview
MS-98H2
Brand: MSI Pages: 42
StarTech.com EC4S950 Instruction Manual preview
EC4S950
Brand: StarTech.com Pages: 9
Z3 Technology Z3-DM8107-SDI2-RPS User Instructions preview
Z3-DM8107-SDI2-RPS
Brand: Z3 Technology Pages: 85
ST X-NUCLEO-IHM03A1 User Manual preview
X-NUCLEO-IHM03A1
Brand: ST Pages: 12
Soho CableFREE NetBlaster II NCP110 Features & Benefits preview
CableFREE NetBlaster II NCP110
Brand: Soho Pages: 2
InWin 127 User Manual preview
127
Brand: InWin Pages: 20
Dell EMC NX440 Setting Up Your System preview
NX440
Brand: Dell EMC Pages: 2
Dell EMC SD-WAN Edge 600 Series Setup Manual preview
SD-WAN Edge 600 Series
Brand: Dell EMC Pages: 8
Xtramus LES-5160 Manual preview
LES-5160
Brand: Xtramus Pages: 36

Brands by name

Popular brands

Load more brands