manualshive.com logo in svg

ARM ARM1176JZF-S, Technical Reference Manual

The ARM ARM1176JZF-S Technical Reference Manual is a comprehensive user manual for the ARM1176JZF-S processor. Download this manual for free from manualshive.com, to gain valuable insights into the product's technical specifications, performance, and programming details. Enhance your understanding of this advanced processor with this detailed manual.

Share
Download
background image

System Control Coprocessor 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-121

ID012310

Non-Confidential, Unrestricted Access

As part of the initialization of the DMA channel, the process that uses that channel writes the 
processor Context ID to the DMA Context ID Register. Where the channel is designated as a 
User-accessible channel, the privileged process, that initializes the channel for use in User 
mode, must write the Context ID at the same time that the software writes to the U bit for the 
channel.

The process that translates VAs to physical addresses uses the ASID stored in the bottom eight 
bits of the Context ID register to enable different VA maps to co-exist. Attempts to write this 
register while the DMA channel is Running or Queued has no effect.

Only privileged processes can read this register. This provides anonymity of the DMA channel 
usage from User processes. On a context switch, where the state of the DMA is stacked and 
restored, the saved state must include this register.

If a user process attempts to access this privileged register the processor takes an Undefined 
instruction trap.

3.2.43

c12, Secure or Non-secure Vector Base Address Register

The purpose of the Secure or Non-secure Vector Base Address Register is to hold the base 
address for exception vectors in the Secure and Non-secure worlds. For more information, see 

Exceptions

 on page 2-36.

The Secure or Non-secure Vector Base Address Register is:

•

in CP15 c12

•

a 32-bit read/write register banked in Secure and Non-secure worlds

•

accessible in privileged modes only.

Figure 3-65 shows the arrangement of bits in the register.

Figure 3-65 Secure or Non-secure Vector Base Address Register format

Table 3-121 lists how the bit values correspond with the Secure or Non-secure Vector Base 
Address Register functions.

When an exception occurs in the Secure world, the core branches to address:

Secure Vector_Base_A Exception_Vector_Address.

When an exception occurs in the Non-secure world, the core branches to address:

Non-secure Vector_Base_A Exception_Vector_Address.

When high vectors are enabled, regardless of the value of the register the core branches to:

0xFFFF0000

 + Exception_Vector_Address

Vector base address

31

5 4

0

SBZ

Table 3-121 Secure or Non-secure Vector Base Address Register bit functions

Bits

Field name

Function

[31:5]

Vector base address

Determines the location that the core branches to on an exception

Holds the base address. The reset value is 0.

[4:0]

SBZ

UNP/SBZ.

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

D-Link Express EtherNetwork DFE-670TXD Quick Install Manual preview
Express EtherNetwork DFE-670TXD
Brand: D-Link Pages: 4
DAD DSX 26 User Manual preview
DSX 26
Brand: DAD Pages: 36
D-Link DUB-1320 Quick Install Manual preview
DUB-1320
Brand: D-Link Pages: 2
National Instruments NI 9213 Getting Started preview
NI 9213
Brand: National Instruments Pages: 11
Zhone 6211 Quick Installation Instructions preview
6211
Brand: Zhone Pages: 1
FONESTAR XO-324 Instruction Manual preview
XO-324
Brand: FONESTAR Pages: 8
East Coast Datacom PDS-1/10G User Manual preview
PDS-1/10G
Brand: East Coast Datacom Pages: 19
NCR 7702-K134 Upgrade Manual preview
7702-K134
Brand: NCR Pages: 15
Ista AMF2.0 Operator'S Manual preview
AMF2.0
Brand: Ista Pages: 16
Bridgeworks Tamar FCSAS102800 User Manual preview
Tamar FCSAS102800
Brand: Bridgeworks Pages: 56
Crown PIP-AF Owner'S Manual preview
PIP-AF
Brand: Crown Pages: 7
ADC 150-204-100-03 User Manual preview
150-204-100-03
Brand: ADC Pages: 29
LAWO A_madi4 User Manual preview
A_madi4
Brand: LAWO Pages: 68
Crestron CEN-IO Operation Manual preview
CEN-IO
Brand: Crestron Pages: 36
StarTech.com 8STUSBDUP12 Instruction Manual preview
8STUSBDUP12
Brand: StarTech.com Pages: 20
StarTech.com SATDOCK4U3RE User Manual preview
SATDOCK4U3RE
Brand: StarTech.com Pages: 12
AudioSource AV-THREE Owner'S Manual preview
AV-THREE
Brand: AudioSource Pages: 5
Omron NJ-series Network Connection Manual preview
NJ-series
Brand: Omron Pages: 86

Brands by name

Popular brands

Load more brands