manualshive.com logo in svg

ARM ARM1176JZF-S, Technical Reference Manual

The ARM ARM1176JZF-S Technical Reference Manual is a comprehensive user manual for the ARM1176JZF-S processor. Download this manual for free from manualshive.com, to gain valuable insights into the product's technical specifications, performance, and programming details. Enhance your understanding of this advanced processor with this detailed manual.

Share
Download
background image

Programmer’s Model 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

2-27

ID012310

Non-Confidential, Unrestricted Access

2.10.5

The E bit

ARM and Thumb instructions are provided to set and clear the E-bit. The E bit controls 
load/store endianness. For details of where the E bit is used see Chapter 4 

Unaligned and 

Mixed-endian Data Access Support

.

Architecture versions prior to ARMv6 specify this bit as SBZ. This ensures no endianness 
reversal on loads or stores.

2.10.6

The A bit

The A bit is set automatically. It is used to disable imprecise Data Aborts. It might be not 
writable in the Non-secure world if the AW bit in the SCR register is reset. For details of how 
to use the A bit see 

Imprecise Data Abort mask in the CPSR/SPSR

 on page 2-47.

2.10.7

The control bits

The bottom eight bits of a PSR are known collectively as the 

control bits

. They are the: 

•

Interrupt disable bits

•

T bit

•

Mode bits

 on page 2-28.

The control bits change when an exception occurs. When the processor is operating in a 
privileged mode, software can manipulate these bits.

Interrupt disable bits

The I and F bits are the interrupt disable bits:

•

When the I bit is set, IRQ interrupts are disabled.

•

When the F bit is set, FIQ interrupts are disabled. FIQ can be non-maskable in the 
Non-secure world if the FW bit in SCR register is reset

Note

 You can change the SPSR F bit in the Non-secure world but this does not update the CPSR if 
the SCR bit 4 (FW) does not permit it.

T bit

The T bit reflects the operating state:

•

when the T bit is set, the processor is executing in Thumb state

•

when the T bit is clear, the processor is executing in ARM state, or Jazelle state depending 
on the J bit.

Note

 Never use an MSR instruction to force a change to the state of the T bit in the CPSR. If an MSR 
instruction does try to modify this bit the result is architecturally Unpredictable. In the 
ARM1176JZF-S processor this bit is not affected.

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Salus PL07 Instruction Manual preview
PL07
Brand: Salus Pages: 16
LGC wireless InterReach Fusion SingleStar Installation And Operation Manual preview
InterReach Fusion SingleStar
Brand: LGC wireless Pages: 154
IFM Electronic OVP800 Operating Instructions Manual preview
OVP800
Brand: IFM Electronic Pages: 14
Gundermann VIDEOWALL LEDWALL Optimizer HQ P2 Manual preview
LEDWALL Optimizer HQ P2
Brand: Gundermann VIDEOWALL Pages: 12
netsys NVF-2400S User Manual preview
NVF-2400S
Brand: netsys Pages: 164
Spirent A2-400 Installation Instructions Manual preview
A2-400
Brand: Spirent Pages: 22
Renesas PROM Programming Adapters PCA7438F-64A User Manual preview
PROM Programming Adapters PCA7438F-64A
Brand: Renesas Pages: 18
Riverbed SteelCentral NetExpress 470 Upgrade And Maintenance Manual preview
SteelCentral NetExpress 470
Brand: Riverbed Pages: 140
Netopia D3100-I User Reference Manual preview
D3100-I
Brand: Netopia Pages: 138
YASKAWA CP 040 RS422/485 Manual preview
CP 040 RS422/485
Brand: YASKAWA Pages: 87
Maco RUSTICO 13321 Installation Instructions Manual preview
RUSTICO 13321
Brand: Maco Pages: 8
MSI MS-6593 ATX Instructions preview
MS-6593 ATX
Brand: MSI Pages: 5
D-Link DI-804V Owner'S Manual preview
DI-804V
Brand: D-Link Pages: 52
D-Link DES-1252 - Web Smart Switch Quick Installation Manual preview
DES-1252 - Web Smart Switch
Brand: D-Link Pages: 11
D-Link DES-1228 - Web Smart Switch Specifications preview
DES-1228 - Web Smart Switch
Brand: D-Link Pages: 4
D-Link DHP-347AV Quick Installation Manual preview
DHP-347AV
Brand: D-Link Pages: 32
D-Link DHP-347AV User Manual preview
DHP-347AV
Brand: D-Link Pages: 26
D-Link DI-102 - Load Balancing Device User Manual preview
DI-102 - Load Balancing Device
Brand: D-Link Pages: 17

Brands by name

Popular brands

Load more brands