manualshive.com logo in svg

ARM ARM1176JZF-S, Technical Reference Manual

The ARM ARM1176JZF-S Technical Reference Manual is a comprehensive user manual for the ARM1176JZF-S processor. Download this manual for free from manualshive.com, to gain valuable insights into the product's technical specifications, performance, and programming details. Enhance your understanding of this advanced processor with this detailed manual.

Share
Download
background image

VFP Exception Handling 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

22-3

ID012310

Non-Confidential, Unrestricted Access

22.2

Bounced instructions

Normally, the VFP11 hardware executes floating-point instructions completely in hardware. 
However, the VFP11 coprocessor can, under certain circumstances, refuse to accept a 
floating-point instruction, causing the ARM Undefined Instruction exception. This is known as 

bouncing

 the instruction.

There are three reasons for bouncing an instruction:

•

a prior instruction generates a potential or actual floating-point exception that cannot be 
properly handled by the VFP11 coprocessor, such as a potential underflow when the 
VFP11 coprocessor is not in flush-to-zero mode

•

a prior instruction generates a potential or actual floating-point exception when the 
corresponding exception enable bit is set in the FPSCR, such as a square root of a negative 
value when the IOE bit, FPSCR[8], is set

•

the current instruction is Undefined.

When a floating-point exception is detected, the VFP11 hardware sets the EX flag, FPEXC[31], 
and loads the FPINST register with a copy of the exceptional instruction. The VFP11 
coprocessor is now in the 

exceptional state

. The instruction that bounces as a result of the 

exceptional state is referred to as the 

trigger

 instruction.

See 

Exception processing

 on page 22-8.

22.2.1

Potential or actual exception that the VFP11 coprocessor cannot handle

Three exceptional conditions cannot be handled by the VFP11 hardware:

•

an operation that might underflow when the VFP11 coprocessor is not in flush-to-zero 
mode

•

an operation involving a subnormal operand when the VFP11 coprocessor is not in 
flush-to-zero mode

•

an operation involving a NaN when the VFP11 coprocessor is not in default NaN mode.

For these conditions the VFP11 coprocessor relies on support code to process the operation. See 

Underflow exception

 on page 22-17 and 

Input exceptions

 on page 22-19.

22.2.2

Potential or actual exception with the exception enable bit set

The VFP11 coprocessor evaluates the instruction for exceptions in the E1 and E2 pipeline 
stages. No means exist to signal exceptions to the ARM11 processor after the E2 stage. The 
VFP11 coprocessor enters the exceptional state when it detects that an instruction has a potential 
to generate a floating-point exception while the corresponding exception enable bit is set. Such 
an instruction is called a 

potentially exceptional instruction

.

An example of an instruction that generates an actual exception is a division of a normal value 
by zero when the Division by Zero exception enable bit, FPSCR[9], is set. This mechanism 
provides support for the IEEE 754 trap mechanism and provides programmers a means of 
halting execution on certain conditions.

As an example of an instruction that generates a potential exception, if the overflow exception 
enable bit, FPSCR[10], is set, and the initial exponent for a multiply operation is the maximum 
exponent for a normal value in the destination precision, the VFP11 coprocessor bounces the 
instruction pessimistically. Because the impact on the exponent because of mantissa overflow 
and rounding is not known in the E1 or E2 stages of the FMAC pipeline, the decision to bounce 

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

ekwb EK-FC1080 GTX Ti TF6 Installation Manual preview
EK-FC1080 GTX Ti TF6
Brand: ekwb Pages: 2
SeaLevel 7406e User Manual preview
7406e
Brand: SeaLevel Pages: 17
Alesis QUADRAVERB Service Manual preview
QUADRAVERB
Brand: Alesis Pages: 46
Cateye Urban Wireless CC-VT240W Instruction Manual preview
Urban Wireless CC-VT240W
Brand: Cateye Pages: 15
NEC P401-TMX4D User Manual preview
P401-TMX4D
Brand: NEC Pages: 2
RAK RAK3372 Quick Start Manual preview
RAK3372
Brand: RAK Pages: 30
Cromemco 32K Bytesaver Instruction Manual preview
32K Bytesaver
Brand: Cromemco Pages: 46
Verizon Wireless PC 3220 Owner'S Manual preview
PC 3220
Brand: Verizon Wireless Pages: 39
Altera Nios II Hardware Development Manual preview
Nios II
Brand: Altera Pages: 42
Advantech ARK-1380 User Manual preview
ARK-1380
Brand: Advantech Pages: 50
Lattice Semiconductor iCE40 SPRAM Series Technical Note preview
iCE40 SPRAM Series
Brand: Lattice Semiconductor Pages: 12
ZALMAN RESERATOR1 V2 Installation And Operational Manual preview
RESERATOR1 V2
Brand: ZALMAN Pages: 18
QTech QSW-2900 User Manual preview
QSW-2900
Brand: QTech Pages: 406
IBM 7311-D11 Removal And Replacement Procedures preview
7311-D11
Brand: IBM Pages: 74
Renesas R0E424270CFLE0 User Manual preview
R0E424270CFLE0
Brand: Renesas Pages: 4
ADTRAN 1202052L1 User Manual preview
1202052L1
Brand: ADTRAN Pages: 136
Kordis NCB210X2-DS-AB Datasheet preview
NCB210X2-DS-AB
Brand: Kordis Pages: 31
VANTAS DPA-S50 Owner'S Manual preview
DPA-S50
Brand: VANTAS Pages: 30

Brands by name

Popular brands

Load more brands