ARM ARM1176JZF-S Technical Reference Manual Download Page 258 | Manualshive

Page: 258 / 759

background image

System Control Coprocessor

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-126

ID012310

Non-Confidential, Unrestricted Access

3.2.46

c13, FCSE PID Register

The

c13, Context ID Register

on page 3-128 replaces the FCSE PID Register. Use of the FCSE

PID Register is deprecated.

The FCSE PID Register is:

•

in CP15 c13

•

a 32-bit read/write register banked for Secure and Non-secure worlds

•

accessible in privileged modes only.

Writing to this register globally flushes the BTAC.

Figure 3-68 shows the arrangement of bits in the register.

Figure 3-68 FCSE PID Register format

Table 3-127 lists how the bit values correspond with the FCSE PID Register functions.

Attempts to write to this register in Secure Privileged mode when

CP15SDISABLE

is HIGH

result in an Undefined exception, see

TrustZone write access disable

on page 2-9.

Table 3-128 lists the results of attempted access for each mode.

To use the FCSE PID Register read or write CP15 with:

•

Opcode_1 set to 0

•

CRn set to c13

•

CRm set to c0

•

Opcode_2 set to 0.

For example:

MRC p15, 0, <Rd>, c13, c0, 0

; Read FCSE PID Register

MCR p15, 0, <Rd>, c13, c0, 0

; Write FCSE PID Register

FCSE PID

31

25 24

0

SBZ

Table 3-127 FCSE PID Register bit functions

Bits

Field name

Function

[31:25]

FCSE PID

The purpose of the FCSE PID Register is to provide the ProcID for fast context switch memory
mappings. The MMU uses the contents of this register to map memory addresses in the range
0-32MB.

Identifies a specific process for fast context switch.

Holds the ProcID. The reset value is 0.

[24:0]

-

Reserved.

SBZ.

Table 3-128 Results of access to the FCSE PID Register

Secure Privileged

Non-secure Privileged

User

Read

Write

Read

Write

Secure data

Secure data

Non-secure data

Non-secure data

Undefined exception

«
...
256
257
258
259
260
...
»

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Brand: Lab.gruppen Pages: 35

Brand: T&D Pages: 122

Brand: Alcad Pages: 6

Brand: Alesis Pages: 61

Brand: M86 Security Pages: 309

NIC-FC730i-Mb-2-32G

Brand: H3C Pages: 37

Brand: Advantech Pages: 50

Brand: LevelOne Pages: 3

PFC Chokes PFC3515V Series

Brand: Delta Electronics Pages: 1

DVI-Vision-IP-Fiber

Brand: G&D Pages: 240

Brand: Idis Pages: 18

Brand: TANDBERG Pages: 2

Brand: McIntosh Pages: 44

CP 040 RS422/485

Brand: YASKAWA Pages: 87

Brand: HeimVision Pages: 167

Brand: Enterasys Pages: 808

Brand: Carotron Pages: 10

Aironet 1200 Series

Brand: Cisco Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands