ARM ARM1176JZF-S Technical Reference Manual Download Page 160

Page: 160 / 759

System Control Coprocessor

ARM DDI 0301H

3-28

ID012310

Non-Confidential, Unrestricted Access

Figure 3-15 Processor Feature Register 1 format

Table 3-14 lists how the bit values correspond with the Processor Feature Register 1 functions.

Table 3-15 lists the results of attempted access for each mode.

To use the Processor Feature Register 1 read CP15 with:

•

Opcode_1 set to 0

•

CRn set to c0

•

CRm set to c1

•

Opcode_2 set to 1.

For example:

MRC p15, 0, <Rd>, c0, c1, 1 ;Read Processor Feature Register 1

Reserved

8 7

4 3

16 15

12 11

28 27

24 23

20 19

Microcontroller programmer's model

Security extension

Programmer's model

Table 3-14 Processor Feature Register 1 bit functions

Bits

Field name

Function

[31:28]

Reserved. RAZ

[27:24]

Reserved. RAZ.

[23:20]

Reserved. RAZ.

[19:16]

Reserved. RAZ.

[15:12]

Reserved. RAZ.

[11:8]

Microcontroller programmer’s model

Indicates support for the ARM microcontroller programmer’s model.

0x0

, Not supported by ARM1176JZF-S processors.

[7:4]

Security extension

Indicates support for Security Extensions Architecture v1.

0x1

, ARM1176JZF-S processors support Security Extensions

Architecture v1, TrustZone.

[3:0]

Programmer’s model

Indicates support for standard ARMv4 programmer’s model.

0x1

, ARM1176JZF-S processors support the ARMv4 model.

Table 3-15 Results of access to the Processor Feature Register 1

Secure Privileged

Non-secure Privileged

User

Read

Write

Read

Write

Data

Undefined exception

Data

Undefined exception

Summary of Contents for ARM1176JZF-S























































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ARM1176JZF-S

Reviews:

Related manuals for ARM1176JZF-S

Brands by name

Popular brands

ARM ARM1176JZF-S, Technical Reference Manual

Search results

Summary of Contents for ARM1176JZF-S

Reviews:

Related manuals for ARM1176JZF-S

Brands by name

Popular brands