ARM ARM1176JZF-S Technical Reference Manual Download Page 718 | Manualshive

Page: 718 / 759

background image

Signal Descriptions

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

A-8

ID012310

Non-Confidential, Unrestricted Access

A.5.2

Data port signals

The data port is a 64-bit wide read/write AXI port. The standard AXI read channel, write
channel, and write response channel signal names are suffixed with

RW

, and the

implementation details of the port are:

•

AWID[3:0]

,

WID[3:0]

,

BID[3:0]

,

ARID[3:0]

, and

RID[3:0]

signals are not

implemented

•

the write data bus is implemented as

WDATARW[63:0]

, and therefore the write strobe

signal is implemented as

WSTRBRW[7:0]

•

the read data bus is implemented as

RDATARW[63:0]

•

the

ARSIDEBANDRW[4:0]

output and

AWSIDEBANDRW[4:0]

output signals are

implemented to indicate shared and inner cacheable accesses

•

the

WRITEBACK

output signal is implemented to indicate cache line evictions.

Table A-7 on page A-9 gives more information about the data port AXI implementation. See the
AMBA

®

AXI Protocol V1.0 Specification for details of the other signals on this port.

Table A-6 Instruction read port AXI signal implementation

Name

Direction

Type

Description

ARLENI[3:0]

Output

Read

Burst length that gives the exact number of transfers:

b0000, 1 data transfer

b0001, 2 data transfers

b0010, 3 data transfers

b0011, 4 data transfers, maximum for the instruction read port

ARSIZEI[2:0]

Output

Read

Burst size, always set to b011, indicating 64-bit transfer

ARBURSTI[1:0]

Output

Read

Burst type:

b01, INCR incrementing burst

b10, WRAP Wrapping burst

ARLOCKI[1:0]

Output

Read

Lock type, always set to b00, indicating normal access

ARSIDEBANDI[4:0]

Output

-

Indicates accesses to shared and inner cacheable memory

«
...
716
717
718
719
720
...
»

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Brand: Sangoma Pages: 6

Brand: PaloAlto Networks Pages: 2

ThunderLAN TNETE100A

Brand: Texas Instruments Pages: 179

X-Pedition 2000

Brand: Enterasys Pages: 86

Emulator MCU Board for 38D5 Group M38D59T-RLFS

Brand: Renesas Pages: 4

RabbitCore RCM4400W

Brand: Rabbit Pages: 126

Brand: Supersonic Pages: 46

LIQMAX III ELC-LMT120-ARGB

Brand: ENERMAX Pages: 32

Brand: Dataprobe Pages: 16

Brand: PADAUK Pages: 27

Brand: 3Com Pages: 53

SL6NQ - Xeon 2.4 GHz/533MHz/512 KB CPU Processor 2.4GHz

Brand: Intel Pages: 56

Brand: Classe Audio Pages: 70

Brand: Quantum Pages: 140

Brand: TP-Link Pages: 2

Brand: Datel Pages: 8

Brand: StarTech.com Pages: 8

Brand: StarTech.com Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands