ARM ARM1176JZF-S Technical Reference Manual Download Page 201

Page: 201 / 759

System Control Coprocessor

ARM DDI 0301H

3-69

ID012310

Non-Confidential, Unrestricted Access

3.2.20

c6, Watchpoint Fault Address Register

Access to the Watchpoint Fault Address register through the system control coprocessor is
deprecated, see

CP14 c6, Watchpoint Fault Address Register (WFAR)

on page 13-12.

3.2.21

c6, Instruction Fault Address Register

The purpose of the

Instruction Fault Address Register

(IFAR) is to hold the address of

instructions that cause a prefetch abort.

The IFAR is:

•

in CP15 c6

•

a 32-bit read/write register banked for Secure and Non-secure worlds

•

accessible in privileged modes only.

The Instruction Fault Address Register bits [31:0] contain the Instruction Fault MVA. The reset
value is 0.

Table 3-66 lists the results of attempted access for each mode.

To use the IFAR read or write CP15 with:

•

Opcode_1 set to 0

•

CRn set to c6

•

CRm set to c0

•

Opcode_2 set to 2.

For example:

MRC p15, 0, <Rd>, c6, c0, 2

; Read Instruction Fault Address Register

MCR p15, 0, <Rd>, c6, c0, 2

; Write Instruction Fault Address Register

A write to this register sets the IFAR to the value of the data written. This is useful for a debugger
to restore the value of the IFAR.

3.2.22

c7, Cache operations

The purpose of c7 is to:

•

control these operations:

—

clean and invalidate instruction and data caches, including range operations

—

prefetch instruction cache line

—

Flush Prefetch Buffer

—

flush branch target address cache

—

virtual to physical address translation.

•

implement the

Data Synchronization Barrier

(DSB) operation

•

implement the

Data Memory Barrier

(DMB) operation

Table 3-66 Results of access to the Instruction Fault Address Register

Secure Privileged

Non-secure Privileged

User

Read

Write

Read

Write

Secure data

Non-secure data

Undefined exception

Summary of Contents for ARM1176JZF-S























































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ARM1176JZF-S

Reviews:

Related manuals for ARM1176JZF-S

Brands by name

Popular brands

ARM ARM1176JZF-S, Technical Reference Manual

Search results

Summary of Contents for ARM1176JZF-S

Reviews:

Related manuals for ARM1176JZF-S

Brands by name

Popular brands