ARM ARM1176JZF-S Technical Reference Manual Download Page 163 | Manualshive

Page: 163 / 759

background image

System Control Coprocessor

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-31

ID012310

Non-Confidential, Unrestricted Access

c0, Memory Model Feature Register 0

The purpose of the Memory Model Feature Register 0 is to provide information about the
memory model, memory management, cache support, and TLB operations of the processor.

The Memory Model Feature Register 0 is:

•

in CP15 c0

•

a 32-bit read-only register common to the Secure and Non-secure worlds

•

accessible in privileged modes only.

Figure 3-17 shows the bit arrangement for Memory Model Feature Register 0.

Figure 3-17 Memory Model Feature Register 0 format

Table 3-20 lists how the bit values correspond with the Memory Model Feature Register 0
functions.

Table 3-21 lists the results of attempted access for each mode.

-

-

-

-

-

-

Reserved

31

28 27

24 23

20 19

16 15

12 11

8 7

4 3

0

-

Table 3-20 Memory Model Feature Register 0 bit functions

Bits

Field name

Function

[31:28]

-

Reserved. RAZ.

[27:24]

-

Indicates support for FCSE.

0x1

, ARM1176JZF-S processors support FCSE.

[23:20]

-

Indicates support for the ARMv6 Auxiliary Control Register.

0x1

, ARM1176JZF-S processors support the Auxiliary Control Register.

[19:16]

-

Indicates support for TCM and associated DMA.

0x3

, ARM1176JZF-S processors support ARMv6 TCM and DMA.

[15:12]

-

Indicates support for cache coherency with DMA agent, shared memory.

0x0

, ARM1176JZF-S processors do not support this model.

[11:8]

-

Indicates support for cache coherency support with CPU agent, shared memory.

0x0

, ARM1176JZF-S processors do not support this model.

[7:4]

-

Indicates support for

Protected Memory System Architecture

(PMSA).

0x0

, ARM1176JZF-S processors do not support PMSA

[3:0]

-

Indicates support for

Virtual Memory System Architecture

(VMSA).

0x3

, ARM1176JZF-S processors support:

•

VMSA v7 remapping and access flag.

Table 3-21 Results of access to the Memory Model Feature Register 0

Secure Privileged

Non-secure Privileged

User

Read

Write

Read

Write

Data

Undefined exception

Data

Undefined exception

Undefined exception

«
...
161
162
163
164
165
...
»

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Brand: Yamaha Pages: 6

Brand: Yamaha Pages: 4

Brand: Yamaha Pages: 22

Brand: Yamaha Pages: 49

Brand: RAK Pages: 30

Brand: IDT Pages: 207

Brand: Lanner Pages: 59

Open Standard Module RPX30 EVA-MI V1

Brand: iesy Pages: 9

Brand: Rockwell Automation Pages: 21

Brand: Z-Wave Pages: 42

Brand: ICS ELECTRONICS Pages: 4

Brand: M-system Pages: 4

Brand: Navitar Pages: 1

Brand: SilverStone Pages: 2

Brand: Classe Audio Pages: 70

Brand: VIA Technologies Pages: 2

NVR52A16-16P-4KS2

Brand: Dahua Technology Pages: 13

Wireless G F5D7000

Brand: Belkin Pages: 252

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands