ARM ARM1176JZF-S Technical Reference Manual Download Page 264 | Manualshive

Page: 264 / 759

background image

System Control Coprocessor

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-132

ID012310

Non-Confidential, Unrestricted Access

To use the memory remap registers read or write CP15 with:

•

Opcode_1 set to 0

•

CRn set to c15

•

CRm set to c2

•

Opcode_2 set to 4.

For example:

MRC p15, 0, <Rd>, c15, c2, 4

; Read Peripheral Port Memory Remap Register

MCR p15, 0, <Rd>, c15, c2, 4

; Write Peripheral Port Memory Remap Register

3.2.50

c15, Secure User and Non-secure Access Validation Control Register

The purpose of the Secure User and Non-secure Access Validation Control Register is to
control:

•

access to the system validation registers in User mode and in the Non-secure world

•

access to the performance monitor unit registers in User mode.

Table 3-134 lists the purpose of the individual bits in the register.

The Secure User and Non-secure Access Validation Control Register is:

•

in CP15 c15

•

a 32-bit read/write register in the Secure world only

•

accessible in privileged modes only.

Figure 3-72 shows the bit arrangement for the Secure User and Non-secure Access Validation
Control Register.

Figure 3-72 Secure User and Non-secure Access Validation Control Register format

Table 3-134 lists how the bit values correspond with the Secure User and Non-secure Access
Validation Control Register functions.

Attempts to write to this register in Secure Privileged mode when

CP15SDISABLE

is HIGH

result in an Undefined exception, see

TrustZone write access disable

on page 2-9.

V

SBZ

31

1 0

Table 3-134 Secure User and Non-secure Access Validation Control Register bit functions

Bits

Field name

Function

[31:1]

-

UNP/SBZ.

[0]

V

Controls access to system validation registers from User and Non-secure modes, and to
performance monitor registers in User mode.

0 = system validation registers accessible only from Secure privileged modes, performance
monitor registers accessible only from privileged modes. The reset value is 0.

1 = system validation and performance monitor registers accessible from any mode.

«
...
262
263
264
265
266
...
»

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Brand: Cabletron Systems Pages: 21

Brand: Data Translation Pages: 60

Brand: IEI Technology Pages: 19

Brand: IEI Technology Pages: 87

Brand: IEI Technology Pages: 3

Brand: Taiwan Commate Computer Inc. Pages: 29

Brand: Moxa Technologies Pages: 2

Brand: Cervoz Pages: 22

Quadro M6000 Sync

Brand: Nvidia Pages: 8

SiliconDrive SSD-P16G(I)-3100

Brand: Silicon Systems Pages: 108

Brand: ADLINK Technology Pages: 86

Brand: HighPoint Pages: 12

Brand: Alphacool Pages: 9

BPN-SAS3-LB16A-N10

Brand: Supermicro Pages: 11

Homecraft Rolyan AA6240

Brand: Patterson Pages: 2

Brand: Paradyne Pages: 10

Brand: ICS Advent Pages: 30

Brand: A.E.B. Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands