ARM ARM1176JZF-S Technical Reference Manual Download Page 721

Page: 721 / 759

Signal Descriptions

ARM DDI 0301H

A-11

ID012310

Non-Confidential, Unrestricted Access

•

the read data bus is implemented as

RDATAD[63:0]

•

the

ARSIDEBANDD[4:0]

output and

AWSIDEBANDD[4:0]

output signals are

implemented to indicate shared and inner cacheable accesses

•

the

WRITEBACK

output signal is implemented to indicate cache line evictions.

The DMA port is a 64-bit wide AXI port that is read/write. Table A-9 lists the DMA port signals.

Table A-9 DMA port signals

Name

Direction

Type

Description

AWLEND[3:0]

Output

Write

Write burst length:

b0000, 1 data transfer

b0001, 2 data transfers

b0010, 3 data transfers

b0011, 4 data transfers, maximum for the DMA port.

AWSIZED[2:0]

Output

Write

Write burst size:

b000, indicating 8-bit transfer

b001, indicating 16-bit transfer

b010, indicating 32-bit transfer

b011, indicating 64-bit transfer.

AWBURSTD[1:0]

Output

Write

Write burst type:

b00, FIXED, fixed burst

b01, INCR, incrementing burst.

AWLOCKD[1:0]

Output

Write

Write lock type, always set to b00, indicating normal access.

ARLEND[3:0]

Output

Read

Burst length that gives the exact number of transfer:

b0000, 1 data transfer

b0011, 4 data transfers.

ARSIZED[2:0]

Output

Read

Burst size:

b000, indicating 8-bit transfer

b001, indicating 16-bit transfer

b010, indicating 32-bit transfer

b011, indicating 64-bit transfer.

ARBURSTD[1:0]

Output

Read

Burst type:

b00, FIXED, fixed burst

b01, INCR, incrementing burst.

ARLOCKD[1:0]

Output

Read

Lock type, always set to b00, indicating normal access.

ARSIDEBANDD[4:0]

Output

Read

Indicates read accesses to shared and inner cacheable memory.

AWSIDEBANDD[4:0]

Output

Write

Indicates write accesses to shared and inner cacheable memory.

Summary of Contents for ARM1176JZF-S























































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ARM1176JZF-S

Reviews:

Related manuals for ARM1176JZF-S

Brands by name

Popular brands

ARM ARM1176JZF-S, Technical Reference Manual

Search results

Summary of Contents for ARM1176JZF-S

Reviews:

Related manuals for ARM1176JZF-S

Brands by name

Popular brands