manualshive.com logo in svg

ARM ARM1176JZF-S, Technical Reference Manual

The ARM ARM1176JZF-S Technical Reference Manual is a comprehensive user manual for the ARM1176JZF-S processor. Download this manual for free from manualshive.com, to gain valuable insights into the product's technical specifications, performance, and programming details. Enhance your understanding of this advanced processor with this detailed manual.

Share
Download
background image

Level Two Interface 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

8-11

ID012310

Non-Confidential, Unrestricted Access

AxSIZE[2:0]

This signal indicates the size of each transfer. Table 8-3 shows the supported transfer sizes.

AxBURST[1:0]

The 

AxBURST[1:0]

 signals indicate a fixed, incrementing or wrapping burst. Table 8-4 shows 

the burst types that the ARM1176JZF-S processor supports.

The processor uses:

•

Wrapping bursts for some cache line fills

•

Incrementing bursts for accesses to noncacheable memory, including instruction fetches.

AxLOCK[1:0]

The 

AxLOCK[1:0]

 signal indicates the lock type of access. The processor supports all locked 

type accesses. The instruction port only generates Normal access types. The DMA port only 
generates Normal access types. The Data Read/Write port generates all access types, Normal, 
exclusive and locked access.

Table 8-5 shows the values of 

AxLOCK

 that the processor supports.

Table 8-3 AxSIZE[2:0] encoding

AxSIZE[2:0]

Bytes in transfer

b000

1

b001

2

b010

4

b011

8

Table 8-4 AxBURST[1:0] encoding

AxBURST[2:0]

Burst type

Description

b00

Fixed

Fixed address burst

b01

Incr

Incrementing address burst

b10

Wrap

Incrementing address burst that wraps to a lower address at the wrap boundary

Table 8-5 AxLOCK[1:0] encoding

AxLOCK[1:0]

Description

b00

Normal access

b01

Exclusive access

b10

Locked access

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Idis DR-8416 Operation Manual preview
DR-8416
Brand: Idis Pages: 123
Idis DR-6232H Installation Manual preview
DR-6232H
Brand: Idis Pages: 29
Idis DR-4516P Installation Manual preview
DR-4516P
Brand: Idis Pages: 28
Idis DirectIP DR-1304P Operation Manual preview
DirectIP DR-1304P
Brand: Idis Pages: 82
TE Connectivity InterReach Fusion ADCP-77-044 Manual preview
InterReach Fusion ADCP-77-044
Brand: TE Connectivity Pages: 236
Cypress Semiconductor CY7C1034DV33 Specification Sheet preview
CY7C1034DV33
Brand: Cypress Semiconductor Pages: 9
Genie WONVR216P5 Quick Start Manual preview
WONVR216P5
Brand: Genie Pages: 15
Multitech MultiConnect SE MTS2EA Quick Start Manual preview
MultiConnect SE MTS2EA
Brand: Multitech Pages: 8
HARTING HAIIC MICA Hardware Development Manual preview
HAIIC MICA
Brand: HARTING Pages: 13
M86 Security M86 Web Filter User Manual preview
M86 Web Filter
Brand: M86 Security Pages: 309
Moxa Technologies TAP-125 Series User Manual preview
TAP-125 Series
Brand: Moxa Technologies Pages: 51
Aaeon SBC-555 Manual preview
SBC-555
Brand: Aaeon Pages: 72
Alvarion BreezeNET DS.11 Configuration Utility Release Note preview
BreezeNET DS.11 Configuration Utility
Brand: Alvarion Pages: 2
Beck com.tom INDUSTRY 100.WLAN.W Startup Manual preview
com.tom INDUSTRY 100.WLAN.W
Brand: Beck Pages: 2
ADC 150-204-100-03 User Manual preview
150-204-100-03
Brand: ADC Pages: 29
AXIOMTEK IPC934-230-FL Quick Installation Manual preview
IPC934-230-FL
Brand: AXIOMTEK Pages: 2
Atmel SAMA5D31-EK User Manual preview
SAMA5D31-EK
Brand: Atmel Pages: 123
National Instruments DAQ X NI 634 Series User Manual preview
DAQ X NI 634 Series
Brand: National Instruments Pages: 278

Brands by name

Popular brands

Load more brands