manualshive.com logo in svg

Agilent Technologies B1542A, User Manual

Share
Download
Agilent Technologies B1542A User Manual Download Page 97

Agilent B1542A User’s Guide, Edition 4

5- 19

PLSDIV Test Definitions

PLSDIV IdVd

Extended Test 
Parameters

The following parameters are available to set the test condition. For more details, 
see “Parameters” on page 5-31.

TransTime 

Pulse leading/trailing edge transition time, in s. 2 ns to 500 ns, 3 
digits or 1 ns resolution.

MeasTime 

Measurement timing at the pulse top. 0 to 1, 3 digits or 0.01 
resolution.

SmplNum 

Oscilloscope sampling number. 16 to 262144, 6 digits or 1 step.

SmthNum 

Oscilloscope smoothing number. 3 to 4001, 4 digits or 1 step.

SmthStat 

Status of the oscilloscope smoothing. Enable or Disable.

AvgNum 

Oscilloscope averaging number. 1 to 4095, 4 digits or 1 step.

VdAdjust 

Status of the drain voltage automatic adjustment. Enable or 
Disable. 

VgAdjust 

Status of the gate voltage automatic adjustment. Enable or 
Disable.

RangingMode 

Measurement ranging mode. Auto or Fixed.

ConnectChk 

Status of the connection check at initialization. Enable or 
Disable.

GateZero 

Status of the gate monitor channel zero measurement at 
initialization. Enable or Disable.

DcSwitch 

Availability of the pulse/dc switch units. Yes (exists, pulsed IV 
measurement connection will be made) or No (none).

SWAddress 

GPIB address of the 11713A switch controller. Integer, 1 to 32.

Summary of Contents for B1542A



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands