manualshive.com logo in svg

Agilent Technologies B1542A, User Manual

Share
Download
Agilent Technologies B1542A User Manual Download Page 43

Agilent B1542A User’s Guide, Edition 4

2- 23

Installation

Software Installation

Updating Software

Perform the following procedure to update the pulsed IV system software.

1. Install the latest revision of the pulsed IV system software. See “Installing 

Software” on page 2-21.

2. Launch EasyEXPERT or Desktop EasyEXPERT. And click the Start 

EasyEXPERT button.

3. Open your workspace or create a new workspace.

4. Display the Application Test tab screen.

5. Remove checks from categories except for the Pulsed IV in the Category list.

6. Right-click a pulsed IV test definition in the Library list and click Delete 

Definition of This Test to open the confirmation dialog box. And click OK to 
delete the test definition from the present workspace.

Repeat this to delete all of the pulsed IV test definitions.

7. Import the pulsed IV test definitions from the following folder.

C:\Program Files\Agilent\PLSDIV\TestDefinitions

NOTE

You do not need to perform “Installing Cable Compensation Data” on page 2-21 
and “Compensation” on page 3-11.

If You Remove Pulsed IV Software

Launch the Add or Remove Programs from the Control Panel and remove the 
programs in the following order.

1. Agilent Technologies PLSDIV Drain Setup

2. Agilent Technologies B1542A-Opt003

3. Agilent Technologies PLSDIV A.01.02

4. Agilent Technologies PLSDIV A.01.00 or A.01.01

Summary of Contents for B1542A



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands