manualshive.com logo in svg

Agilent Technologies B1542A, User Manual

Share
Download
Agilent Technologies B1542A User Manual Download Page 13

Agilent B1542A User’s Guide, Edition 4

1- 5

Introduction

Overview

Table 1-1

DC Source Monitor Supported by Agilent B1542A or B1542A-003

Table 1-2

Pulse Generator Supported by Agilent B1542A

Table 1-3

Oscilloscope Supported by Agilent B1542A

Agilent Model Number

Remarks

B1500A

Firmware revision A.02.00 or later

E5260A

Firmware revision B.01.00

E5262A or E5263A

Firmware revision B.01.00 (not available for the 
DC + pulsed IV test system or the E1542A-024)

E5270B

Firmware revision B.01.00

4155B/C or 4156B/C

HOSTC 3.06, SMUC 4.07, ADC 1.00 

 

(for Desktop EasyEXPERT A.02.00)

HOSTC 3.07, SMUC 4.08, ADC 1.00 

 

(for Desktop EasyEXPERT A.03.00 or later)

Agilent Model Number

Remarks

81101A

50 MHz output, standalone

8110A with 81103A

150 MHz output, modular

81110A with 81111A

165 MHz output, modular

Agilent Model Number

Remarks

54852A

2 GHz, 4 channels, 10 GSa/s, revision A.05.01

54853A

2.5 GHz, 4 channels, 20 GSa/s, revision A.05.01

54854A

4 GHz, 4 channels, 20 GSa/s, revision A.05.01

54855A

6 GHz, 4 channels, 20 GSa/s, revision A.05.01

DSO8000A series

600 MHz or 1 GHz, 4 channels, 4 GSa/s, revision 
A.05.00

DSO80000B series

2/3/4/6/8/10/12/13 GHz, 4 channels, 40 GSa/s 
when using 1 or 2 channels, 20 GSa/s when using 
all channels, revision A.05.01

Summary of Contents for B1542A



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands