manualshive.com logo in svg

Agilent Technologies B1542A, User Manual

Share
Download
Agilent Technologies B1542A User Manual Download Page 151

Agilent B1542A User’s Guide, Edition 4

7- 13

Status Code and Error Messages

SYSPIV_ERROR_SAC_PIV_INIT_NOT_COMPL
ETED

BFFC10A4

-4260

PlsdivSetAdjustConf: Execute 
PlsdivInit before this command.

SYSPIV_ERROR_SAS_ADJ_TERM

BFFC10A8

-4264

PlsdivSetAdjustStat: Terminal must 
be 0: gate or 1: drain.

SYSPIV_ERROR_SAS_ADJ_STAT

BFFC10A9

-4265

PlsdivSetAdjustStat: Adjustment 
status must be 0: OFF or 1: ON.

SYSPIV_ERROR_SAS_PIV_INIT_NOT_COMPLE
TED

BFFC10AA

-4266

PlsdivSetAdjustStat: Execute 
PlsdivInit before this command.

SYSPIV_ERROR_SA_PIV_INIT_NOT_COMPLET
ED

BFFC10AC

-4268

PlsdivSetAveraging: Execute 
PlsdivInit before this command.

SYSPIV_ERROR_SDD_DEVICE_DELAY_OUT_
OF_RANGE

BFFC10AE

-4270

PlsdivSetDeviceDelay: device_delay 
must be 

-

1 us to +1 us.

SYSPIV_ERROR_SDD_PIV_INIT_NOT_COMPL
ETED

BFFC10AF

-4271

PlsdivSetDeviceDelay: Execute 
PlsdivInit before this command.

SYSPIV_ERROR_SMM_ID_CAL_COMP_STAT

BFFC10B0

-4272

PlsdivSetMeasMode: id 
compensation status must be 0: OFF 
or 1: ON.

SYSPIV_ERROR_SMM_ID_LOSS_COMP_STAT

BFFC10B1

-4273

PlsdivSetMeasMode: id loss 
compensation status must be 0: OFF 
or 1: ON.

SYSPIV_ERROR_SMM_VG_MON_COMP_STAT

BFFC10B2

-4274

PlsdivSetMeasMode: vg monitor 
compensation status must be 0: OFF 
or 1: ON.

SYSPIV_ERROR_SMM_VD_MON_COMP_STAT

BFFC10B3

-4275

PlsdivSetMeasMode: vd monitor 
compensation status must be 0: OFF 
or 1: ON.

SYSPIV_ERROR_SMM_VG_DIV_COMP_STAT

BFFC10B4

-4276

PlsdivSetMeasMode: vd divider 
compensation status must be 0: OFF 
or 1: ON.

Status Code Name

Status Code

Error 

Number

Error Message

Summary of Contents for B1542A



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands