manualshive.com logo in svg

Agilent Technologies B1542A, User Manual

Share
Download
Agilent Technologies B1542A User Manual Download Page 159

Agilent B1542A User’s Guide, Edition 4

7- 21

Status Code and Error Messages

Table 7-3

Digital Sampling Oscilloscope Driver Error

DVRPGU_ERROR_OFFSET_TOO_LARGE

BFFC0E48

-3656

Offset value must be =< +10 V.

DVRPGU_ERROR_OFFSET_TOO_SMALL

BFFC0E49

-3657

Offset value must be >= 

-

10 V.

DVRPGU_ERROR_INT_IMP_INVALID

BFFC0E4A

-3658

Internal impedance must be 50 ohm or 
1 Mohm.

DVRPGU_ERROR_EXT_IMP_INVALID

BFFC0E4B

-3659

External impedance must be 50 ohm to 
1 Mohm.

Status Code Name

Status 

Code

Error 

Number

Error Message

Status Code Name

Status 

Code

Error 

Number

Error Message

DVRSCOPE_NO_ERROR

0

0

No error.

DVRSCOPE_ERROR_SELF_TEST_PASSED

0

0

Selftest passed.

DVRSCOPE_VI_ERROR_SYSTEM_ERROR

BFFC0F00

-3840

System error occurred.

DVRSCOPE_INSTR_ERROR_NULL_PTR

BFFC0F01

-3841

NULL pointer was detected.

DVRSCOPE_INSTR_ERROR_RESET_FAILED

BFFC0F02

-3842

Reset operation failed. Reboot the 
instrument.

DVRSCOPE_INSTR_ERROR_UNEXPECTED

BFFC0F03

-3843

Unexpected error occurred.

DVRSCOPE_INSTR_ERROR_DETECTED

BFFC0F04

-3844

Instrument error occurred.

DVRSCOPE_INSTR_NO_LAST_COMMA

BFFC0F05

-3845

Nth comma is not found in IDN string.

DVRSCOPE_INSTR_INV_ASCII_NUMBER

BFFC0F06

-3846

ASCII to numeric conversion error.

DVRSCOPE_INSTR_ERROR_PARAMETER1

BFFC0F10

-3856

Invalid value for parameter 1.

DVRSCOPE_INSTR_ERROR_PARAMETER2

BFFC0F11

-3857

Invalid value for parameter 2.

DVRSCOPE_INSTR_ERROR_PARAMETER3

BFFC0F12

-3858

Invalid value for parameter 3.

DVRSCOPE_INSTR_ERROR_PARAMETER4

BFFC0F13

-3859

Invalid value for parameter 4.

DVRSCOPE_INSTR_ERROR_PARAMETER5

BFFC0F14

-3860

Invalid value for parameter 5.

Summary of Contents for B1542A



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands