manualshive.com logo in svg

Agilent Technologies B1542A, User Manual

Share
Download
Agilent Technologies B1542A User Manual Download Page 126

6- 12

Agilent B1542A User’s Guide, Edition 4

PLSDIV TIS Commands

PlsdivCaptureTimeData

PlsdivCaptureTimeData

This command reads the oscilloscope horizontal data (time data).

Execution 
Conditions

PlsdivSetSampling and PlsdivMeasureId must be executed before this command.

The PlsdivSetSampling command 

sampling_num

 parameter value must not be 0.

Filename 

PlsdivCaptureTimeData.exe

Write Type

String

Read Type

List

Write String

This command needs the following input parameter.

sampling_num 

Sampling number of oscilloscope. Numeric value, 16 to 
262144. The value must be the same as the 

sampling_num

 

parameter value set to the PlsdivSetSampling command.

Read List

This command returns the following output parameter.

read_data 

Oscilloscope horizontal data (time data). Vector data. The 
number of returned data is 

sampling_num

 if the smoothing is 

off or the number of data displayed on the oscilloscope screen if 
the smoothing is on. The smoothing on/off is set by the 
PlsdivSetSmoothing command.

Response 

Number of returned data. Numeric value.

Summary of Contents for B1542A



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands