manualshive.com logo in svg

Agilent Technologies B1542A, User Manual

Share
Download
Agilent Technologies B1542A User Manual Download Page 103

Agilent B1542A User’s Guide, Edition 4

5- 25

PLSDIV Test Definitions

PLSDIV IV SMU

PLSDIV IV SMU

Available for Desktop EasyEXPERT Offline mode with the option B1542A-003. 
This test definition controls SMUs to force the primary and secondary sweep 
voltage, measures current, and displays the I-V characteristics.

Device Parameters

The following parameter is available to set the test condition.

IDispRange 

Maximum value of the Y1 axis, in A. 1 mA to 100 mA, 6 digits 
or 1 fA resolution.

Test Parameters

The following parameters are available to set the source output.

SMU1 

Channel number of the SMU used for the primary sweep 
source. Slot1 to Slot8. Maximum channel number depends on 
the configuration of DC source monitor.

StartV1 

Primary sweep start voltage. 

-

100 to 100 V, 6 digits or 1 

μ

V 

resolution.

StopV1 

Primary sweep stop voltage. 

-

100 to 100 V, 6 digits or 1 

μ

V 

resolution.

StepV1 

Primary sweep step voltage. 

-

100 to 100 V, 6 digits or 1 

μ

V 

resolution.

Comp1 

Primary sweep current compliance, in A. 

-

100 mA to 100 mA, 

6 digits or 1 fA resolution.

•

StartV1, StopV1, StepV1

The parameters set the primary sweep source used to apply the drain voltage. 
The number of sweep points is given by the following formula. Then ignore the 
numbers after the decimal point.

Number of sweep points = (StopV1

-

StartV1) /  1

•

StartV2, StopV2, StepV2

The parameters set the secondary sweep source used to apply the gate voltage. 
The number of sweep points is given by the following formula. Then ignore the 
numbers after the decimal point.

Number of sweep points = (StopV2

-

StartV2) /  1

Summary of Contents for B1542A



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands