manualshive.com logo in svg

Agilent Technologies B1542A, User Manual

Share
Download
Agilent Technologies B1542A User Manual Download Page 158

7- 20

Agilent B1542A User’s Guide, Edition 4

Status Code and Error Messages

DVRPGU_ERROR_OFFSET_ON_CONFIG_FILE

BFFC0E2C

-3628

Invalid offset description. Reinstall the 
pulsed IV software.

DVRPGU_ERROR_INT_IMP_ON_CONFIG_FILE

BFFC0E2D

-3629

Invalid internal impedance description. 
Reinstall the pulsed IV software.

DVRPGU_ERROR_EXT_IMP_ON_CONFIG_FILE

BFFC0E2E

-3630

Invalid external impedance description. 
Reinstall the pulsed IV software.

DVRPGU_ERROR_PGU_TYPE_NOT_MATCH

BFFC0E30

-3632

Instrument IDN does not match. Use 
the supported instrument.

DVRPGU_ERROR_CH_NOT_AVAILABLE

BFFC0E31

-3633

Specified channel is not installed. Use 
the channel installed.

DVRPGU_ERROR_DEVICE_IS_BUSY

BFFC0E32

-3634

Device is busy. Reset or reboot the 
instrument.

DVRPGU_ERROR_DEVICE_NOT_OPENED

BFFC0E33

-3635

Device is not ready. Connect the GPIB 
cable properly.

DVRPGU_ERROR_SELF_TEST_FAILED

BFFC0E34

-3636

Selftest failed.

DVRPGU_ERROR_SELF_CAL_FAILED

BFFC0E35

-3637

Calibration failed.

DVRPGU_ERROR_PERIOD_TOO_LONG

BFFC0E40

-3648

Period value must be =< 999.5 s or 
width +3.03 ns.

DVRPGU_ERROR_PERIOD_TOO_SHORT

BFFC0E41

-3649

Period must be >= 6.06 ns.

DVRPGU_ERROR_WIDTH_TOO_LONG

BFFC0E42

-3650

Width value must be =< 999 s.

DVRPGU_ERROR_WIDTH_TOO_SHORT

BFFC0E43

-3651

Width must be >= 3.03 ns.

DVRPGU_ERROR_TRANSITION_TOO_LONG

BFFC0E44

-3652

Transition time must be =< 200 ms or 
width/2.

DVRPGU_ERROR_TRANSITION_TOO_SHORT

BFFC0E45

-3653

Transition time must be >= 2 ns.

DVRPGU_ERROR_AMP_TOO_LARGE

BFFC0E46

-3654

Amplitude must be =< 10 V for 50 ohm 
system or 20 V for other cases.

DVRPGU_ERROR_AMP_TOO_SMALL

BFFC0E47

-3655

Amplitude must be >= 100 mV for 50 
ohm system or 200 mV for other cases.

Status Code Name

Status 

Code

Error 

Number

Error Message

Summary of Contents for B1542A



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands