manualshive.com logo in svg

Agilent Technologies B1542A, User Manual

Share
Download
Agilent Technologies B1542A User Manual Download Page 144

7- 6

Agilent B1542A User’s Guide, Edition 4

Status Code and Error Messages

SYSPIV_ERROR_NULL_MESSAGE_PTR

BFFC1040

-4160

PlsdivErrorMessage: Specify the 
variable used for error message.

SYSPIV_ERROR_NULL_ERR_NUM_PTR

BFFC1041

-4161

PlsdivErrorMessage: Specify the 
variable used for error number.

SYSPIV_UNKNOWN_ERROR_CODE

BFFC1042

-4162

PlsdivErrorMessage: Unknown error 
code was detected.

SYSPIV_ERROR_FVD_PIV_INIT_NOT_COMPL
ETED

BFFC1044

-4164

PlsdivForceVd: Execute PlsdivInit 
before this command.

SYSPIV_ERROR_FVD_VD_OUT_OF_RANGE

BFFC1045

-4165

PlsdivForceVd: Correct the vd value. 
It must be 

-

10 V =< vd =< 10 V.

SYSPIV_ERROR_FVG_PIV_INT_NOT_COMPLE
TED

BFFC1048

-4168

PlsdivForceVg: Execute PlsdivInit 
before this command.

SYSPIV_ERROR_FVG_PIV_SET_PULSE_WIDT
H_NOT_COMPLETED

BFFC1049

-4169

PlsdivForceVg: Execute 
PlsdivSetPulseWidth before this 
command.

SYSPIV_ERROR_FVG_PIV_SET_VG_LEVEL_N
OT_COMPLETED

BFFC104A

-4170

PlsdivForceVg: Execute 
PlsdivSetVgLevel before this 
command.

SYSPIV_ERROR_FVG_PIV_SET_SMTH_NOT_C
OMPLETED

BFFC104B

-4171

PlsdivForceVg: Execute 
PlsdivSetSmoothing before this 
command.

SYSPIV_ERROR_FVG_VG_MON_NULL

BFFC104C

-4172

PlsdivForceVg: Specify the variable 
used for vg_mon.

SYSPIV_ERROR_FVG_CONV_STAT_NULL

BFFC104D

-4173

PlsdivForceVg: Specify the variable 
used for conv_stat.

SYSPIV_ERROR_INIT_INVALID_STAT_CHK_C
NNT

BFFC1050

-4176

PlsdivInit: The connect check status 
must be 0: OFF or 1: ON.

SYSPIV_ERROR_INIT_INVALID_STAT_ZERO_C
ANCEL

BFFC1051

-4177

PlsdivInit: The gate zero status must 
be 0: OFF or 1: ON.

Status Code Name

Status Code

Error 

Number

Error Message

Summary of Contents for B1542A



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands