manualshive.com logo in svg

Agilent Technologies B1542A, User Manual

Share
Download
Agilent Technologies B1542A User Manual Download Page 127

Agilent B1542A User’s Guide, Edition 4

6- 13

PLSDIV TIS Commands

PlsdivCutoffVd

PlsdivCutoffVd

This command applies 0 V drain voltage and sets the SMU output switch off.

Filename 

PlsdivCutoffVd.exe

Response 

Status code. Numeric value. To read error message, use PlsdivErrorMessage. If no 
error is detected by this command execution, 0 is returned.

PlsdivCutoffVg

This command sets the PGU output switch off.

Filename 

PlsdivCutoffVg.exe

Response 

Status code. Numeric value. To read the error message, use PlsdivErrorMessage. If 
no error is detected by this command execution, 0 is returned.

PlsdivErrorMessage

This command returns the error number and error message for the specified status 
code. For the error code and message, see “Status Code and Error Messages” on 
page 7-1.

Filename 

PlsdivErrMessage.exe

Write Type

String

Read Type

String

Write String

This command needs the following input parameter.

status_code 

Status code returned by a command. Numeric value.

Read String

This command returns the following output parameter.

message 

Error message specified by the 

status_code

 parameter. The 

message is a string up to 256 characters.

Response 

Error number specified by the 

status_code

 parameter. Numeric value.

Summary of Contents for B1542A



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands