manualshive.com logo in svg

Agilent Technologies B1542A, User Manual

Share
Download
Agilent Technologies B1542A User Manual Download Page 142

7- 4

Agilent B1542A User’s Guide, Edition 4

Status Code and Error Messages

SYSPIV_ERROR_PARAMETER14

BFFC101D

-4125

Invalid value for parameter 14.

SYSPIV_ERROR_PARAMETER15

BFFC101E

-4126

Invalid value for parameter 15.

SYSPIV_ERROR_PARAMETER16

BFFC101F

-4127

Invalid value for parameter 16.

SYSPIV_ERROR_CPM_PIV_SET_SAMPLING_N
OT_COMPLETED

BFFC1020

-4128

PlsdivCaptureMonData: Execute 
PlsdivSetSampling before this 
command.

SYSPIV_ERROR_CPM_SAMPLING_NUM_DEFI
NITION

BFFC1021

-4129

PlsdivCaptureMonData: Define the 
sampling number in 
PlsdivSetSampling. Do not set 0.

SYSPIV_ERROR_CPM_MEASURE_ID_NOT_CO
MPLETED

BFFC1022

-4130

PlsdivCaptureMonData: Execute 
PlsdivMeasureId before this 
command.

SYSPIV_ERROR_CPM_SAMPLING_NUM_INCO
MPATIBLE

BFFC1023

-4131

PlsdivCaptureMonData: Define the 
same value as the sampling number 
specified by PlsdivSetSampling.

SYSPIV_ERROR_CPM_DRAIN_MODE_INVALI
D

BFFC1024

-4132

PlsdivCaptureMonData: The drain 
data type must be 0: voltage or 1: 
current.

SYSPIV_ERROR_CPM_RET_PTR_NULL

BFFC1025

-4133

PlsdivCaptureMonData: Specify the 
variable used for read_data.

SYSPIV_ERROR_CPS_PIV_SET_SAMPLING_N
OT_COMPLETED

BFFC1028

-4136

PlsdivCapturePulseShape: Execute 
PlsdivSetSampling before this 
command.

SYSPIV_ERROR_CPS_SAMPLING_NUM_DEFI
NITION

BFFC1029

-4137

PlsdivCapturePulseShape: Define the 
sampling number in 
PlsdivSetSampling. Do not set 0.

SYSPIV_ERROR_CPS_MEASURE_ID_NOT_CO
MPLETED

BFFC102A

-4138

PlsdivCapturePulseShape: Execute 
PlsdivMeasureId before this 
command.

Status Code Name

Status Code

Error 

Number

Error Message

Summary of Contents for B1542A



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands