manualshive.com logo in svg

Agilent Technologies B1542A, User Manual

Share
Download
Agilent Technologies B1542A User Manual Download Page 58

3- 10

Agilent B1542A User’s Guide, Edition 4

Performing System Setup and Compensation

System Configuration

System Configuration

Perform this action after completing the system installation or after changing a 
channel assignment or after changing the GPIB address of the system components. 

1. Open the PLSDIV Setup test setup from your preset group.

2. Set the Action field to 

System Configuration

.

3. Click the Single button at the upper right corner on the EasyEXPERT/Desktop 

EasyEXPERT screen. The Configuration dialog box is displayed.

4. Set the system configuration parameters by using the Configuration dialog box. 

See Table 3-2.

Table 3-2

System Configuration Parameters

Field name

Description

Controller

Select 

B1500A Internal

 or 

External PC

.

Visa Name

Enter the VISA interface ID of the GPIB interface.

Instrumentations

PGU

Specify the pulse generator to be used.

DSO

Specify the oscilloscope to be used.

SMU

Specify the DC source monitor to be used.

USB Address

If Controller=

B1500 Internal

, enter the B1500A’s 

internal USB address.

GPIB Address 

a

a. To know the instrument GPIB address, see the manual of each instrument.

PGU, DSO, and SMU

Enter GPIB address of pulse generator (PGU), 
oscilloscope (DSO), and DC source monitor (SMU).

CH Assignment

Gate PGU CH

Enter DSO channel number for Gate pulse output.

Gate Monitor DSO CH

Enter DSO channel number for Gate voltage monitor.

Drain Monitor DSO CH

Enter DSO channel number for Drain voltage monitor.

Drain Bias SMU CH

Enter SMU slot number for Drain voltage output.

Summary of Contents for B1542A



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands