Agilent Technologies B1542A User Manual Download Page 4

Page: 4 / 162

In This Manual

This manual provides the information about Agilent Technologies B1542A and

consists of the following chapters. This manual supports the pulsed IV system

software revision A.01.02.
• Chapter 1, “Introduction”

Describes product overview of Agilent B1542A.

• Chapter 2, “Installation”

Explains how to install Agilent B1542A.

• Chapter 3, “Performing System Setup and Compensation”

Explains how to perform system setup and how to update compensation data.

• Chapter 4, “Performing Measurement”

Describes measurement examples by using the pulsed IV test system.

• Chapter 5, “PLSDIV Test Definitions”

Provides reference information for application test definitions (PLSDIV test

definitions) used for the pulsed IV measurement.

• Chapter 6, “PLSDIV TIS Commands”

Provides reference information for execution files (Plsdiv commands, PLSDIV TIS)

used in the PLSDIV test definitions.

• Chapter 7, “Status Code and Error Messages”

Lists the status code and the error messages.

NOTE

The pulsed IV test system consists of some instruments, oscilloscope, pulse

generator, source monitor unit, and so on. To use the instruments independently or for

details of the instruments, see the manual of each instrument.

NOTE

To get the latest firmware/software/electronic manuals/support information, visit

Agilent Technologies support site (http://www.home.agilent.com), and click

Additional Test & Measurement Products > Parametric Test, click Semiconductor

Parameter/Device Analyzer Series, and click B1500A Semiconductor Device Analyzer.

You can reach Agilent B1500A support site.

Summary of Contents for B1542A



































































































































































Search results

Summary of Contents for B1542A

Reviews:

Brands by name

Popular brands

Agilent Technologies B1542A, User Manual

Search results

Summary of Contents for B1542A

Reviews:

Brands by name

Popular brands