manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 75

CI Troubleshooting

3

75

No peaks

When troubleshooting no peaks, it is important to specify what mode of 
operation is being used, and what expected peaks are not being seen. Always 
start with methane PCI and verify presence of reagent ions. 

No reagent gas peaks in PCI

If the MSD has been working well and nothing seems to have been changed 

•

Wrong tune file loaded, or tune file corrupted

•

Wrong ion polarity (there are no reagent ions visible in NCI)

•

No reagent gas flow; look for background ions, and check pressure

•

Wrong reagent gas selected for the tune file (looking for wrong ions)

•

Large air leak

•

Dirty ion source

•

Poor vacuum (pump problem), see 

page 71

.

If the MSD was recently switched from EI to CI

•

Isolation tip not installed

•

No reagent gas flow

•

Analyzer not sealed (big air leak)

•

Wrong tune file loaded or tune file corrupted

•

Ion source not assembled or connected correctly

•

Wrong reagent gas selected for the tune file (looking for wrong ions)

No PFDTD peaks in PCI

•

Incorrect reagent gas. There are 

no

 PCI PFDTD peaks created with 

isobutane or ammonia. Switch to methane.

•

Analyzer not sealed (big air leak)

•

No calibrant in vial

•

Defective calibration valve(s)

•

Air leak in carrier or reagent gas path

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands