manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 208

208

5977B Series MSD Troubleshooting and Maintenance Manual

7

Analyzer

Analyzer Heaters and Radiators

The ion source and mass filter are housed in cylindrical aluminum tubes 
called radiators (See 

Figure 50

 on page 209) or (See 

Figure 51

 on page 210). 

The radiators control the distribution of heat in the analyzer. They also 
provide electrical shielding for analyzer components. The source heater and 
temperature sensor are mounted in the source heater block. The mass filter 
(quad) heater and temperature sensor are mounted on the mass filter 
radiator. Analyzer temperatures can be set and monitored from the MSD Data 
Acquisition software.

In selecting the temperatures to use, consider the following:

•

Higher temperatures help keep the analyzer clean longer. 

•

Higher ion source temperatures result in more fragmentation and, 
therefore, lower high-mass sensitivity. 

After pumpdown, it takes at least 2 hours for the analyzer to reach thermal 
equilibrium. Data acquired sooner may not be reproducible. 

Recommended settings (for EI operation):

•

Ion source 230 

C

•

Quadrupole 150 

C

The GC/MSD interface, ion source, and mass filter (quad) heated zones 
interact. The analyzer heaters may not be able to accurately control 
temperatures if the setpoint for one zone is much lower than that of an 
adjacent zone. 

C A U T I O N

Do not exceed 200 °C on the quadrupole, or 350 °C on the ion source.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands