manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 58

58

5977B Series MSD Troubleshooting and Maintenance Manual

2

General Troubleshooting

The system is in standby

This message is triggered by a shutdown signal on the remote start cable. It is 
usually caused by a GC fault, an ALS fault, or a bad cable connection. Once the 
cause of the fault is corrected, selecting 

MS ON

 or checking MSD status should 

remove the message.

The system is in vent state

Wait at least 30 minutes after seeing this message before you actually vent the 
MSD.

•

System was vented on purpose (no problem)

•

Fan fault has turned off the high vacuum pump (power cycle the MSD to 
clear the fault)

•

Fuse for the high vacuum pump has failed

•

MSD electronics are not working correctly

There is no emission current

•

Filament is not connected properly; try the other filament

•

Filament has failed; try the other filament

•

MSD electronics are not working correctly

There is not enough signal to begin tune

•

Corrupted tune file

•

Poor mass axis calibration

•

Amu gain or offset is too high

•

Calibration vial(s) empty or almost empty

•

Excessive pressure in the analyzer chamber

•

Air leak

C A U T I O N

Venting the MSD too soon after this message appears can damage the turbo pump.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands