manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 45

General Troubleshooting

2

5977B Series MSD Troubleshooting and Maintenance Manual

45

Mass Spectral Symptoms

This section describes symptoms you might observe in mass spectra. Some of 
these symptoms will appear in the mass spectra of samples. Others you will 
observe only in a tune report. Some of these symptoms have causes that can be 
corrected by the operator. Others, however, require service by an Agilent 
Technologies service representative.

The following symptoms listed under Chromatic symptoms also apply to mass 
spectra:

•

If sensativity is low

•

If repeatability is poor

No peaks

•

Ion source cables not connected

•

Bad connections to or from the detector

•

HED power supply output cable has failed

•

Other electronics failure

•

Incorrect tune file (inappropriate parameters) 

Isotopes are missing or isotope ratios are incorrect

•

Peaks are too wide or too narrow

•

Scan speed is too high (scan mode)

•

Dwell time is too short (SIM mode)

•

Electron multiplier voltage is too high

•

Repeller voltage is too high

•

High background

•

Dirty ion source

High background

•

Pressure in the analyzer chamber is too high

•

Air leak

•

Contamination

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands