manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 163

Vacuum System

6

5977B Series MSD Troubleshooting and Maintenance Manual

163

Side Plate

The side plate for the HES version (See 

Figure 30

 on page 164) or the non-HES 

version (See 

Figure 31

 on page 165) covers the large opening in the side of the 

analyzer chamber. It is attached to the manifold with a hinge. The analyzer 
assembly is attached to the side plate inside the analyzer chamber. The hinge 
allows the side plate to swing away from the manifold for easy access to the 
analyzer.

Several electrical feedthroughs are built into the side plate. Wires connect the 
feedthroughs to analyzer components. The electronic side board is mounted on 
the atmospheric side of the side plate.

Thumbscrews are located at each end of the side plate.

C A U T I O N

Fasten both side plate thumbscrews for shipping or storage only. For normal operation, 
both thumbscrews should be loose. For operation with hydrogen carrier gas, or with 
flammable or explosive CI reagent gases, the front thumbscrew should be fastened just 
finger-tight. Overtightening will warp the side plate and cause air leaks. Do not use a 
tool to tighten the side plate thumbscrews.

C A U T I O N

When you turn on the power to pump down the MSD, press on the side board to ensure 
a good seal. 

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands