manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 91

General Maintenance

4

5977B Series MSD Troubleshooting and Maintenance Manual

91

Before Starting

For your safety, read all of the information in this introduction before 
performing any maintenance tasks.

Scheduled maintenance

Performing common maintenance tasks when scheduled can reduce operating 
problems, prolong system life, and reduce overall operating costs. (See 

Table 9

.)

Keep a record of system performance (tune reports) and maintenance 
operations performed. This makes it easier to identify variations from normal 
operation, and to take corrective action.

Table 9  

Maintenance schedule 

Task

Every week

Every 6 months

Every year

As needed

Tune the MSD

X

Check the foreline pump oil level

X

Check the calibration vial(s)

X

Replace the foreline pump oil

†

X

Replace the DP fluid

X

Check the dry foreline pump

X

Change the dry foreline pump tip seal 

X

Change the foreline pump exhaust filter

X 

Clean the ion source

X 

Check the carrier gas trap(s) on the GC and MSD

X

Replace the worn out parts

X

Lubricate sideplate or vent valve O-rings

*

X

Replace CI Reagent gas supply

X

Replace GC gas supplies

X

†

Every 3 months for CI MSDs using ammonia reagent gas.

*

Vacuum seals other than the side plate O-ring and vent valve O-ring do not need to be lubricated. Lubricating other seals 
can interfere with their correct function.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands