manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 81

CI Troubleshooting

3

81

Large peak at 

m/z

 19

If the abundance of the peak at 

m/z

 19 is more than half abundance of the 

peak at 

m/z

 17, there probably is too much water in the system.

The system was not baked out sufficiently after it was last vented.

Bake out the system as described in the 

Maintenance

 chapter of this manual.

Moisture left over in the reagent gas supply tubing and flow module

Purge the reagent gas supply lines for at least 60 minutes.

Contaminated reagent gas supply

Replace the reagent gas supply, and purge the lines and flow module.

Saturated methane/isobutane gas purifier

Replace the gas purifier.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands