manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 202

202

5977B Series MSD Troubleshooting and Maintenance Manual

7

Analyzer

HES Post extractor lens 1 and 2

The post extractor lenses are part of the lens stack in the EI HES source only. 
A voltage is applied to the two lenses to increase ion focusing through the 
source.

Ion focus

The voltage on the ion focus lens can be varied from 0 to –127 VDC. A typical 
voltage is between –70 and –90 VDC. In general:

•

Increasing the ion focus voltage improves sensitivity at lower masses.

•

Decreasing the ion focus voltage improves sensitivity at higher masses.

•

Incorrect ion focus adjustment results in poor high mass response.

Entrance lens

The entrance lens is at the entrance to the quadrupole mass filter. This lens 
minimizes the fringing fields of the quadrupole which discriminate against 
high-mass ions.

Entrance lens offset

The entrance lens offset (EntOff) controls the fixed voltage applied to the 
entrance lens. It can be varied from 0 to –64 VDC (–20 V is typical). Increasing 
the entrance lens offset generally increases the abundance of ions at low 
masses without substantially decreasing the abundance of high mass ions. 

Entrance lens gain

Entrance lens gain (EntLens) controls the variable voltage applied to the 
entrance lens. It determines how many volts are applied for each 

m/z

. It can be 

varied from 0 to –128 mV/(

m/z

). A typical range is 0 to –40 mV/amu. 

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands