Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 80

Page: 80 / 258

CI Troubleshooting

Excessive noise or low signal-to-noise ratio

The GC inlet needs maintenance.

Refer to the GC manual.

The CI ion source is dirty.

Clean the ion source.

Poor vacuum

Check the pressure on the high vacuum gauge controller.

Air leak

Run Methane Pretune (in PCI). A large peak at

m/z

32 indicates air in the

system. Check for, and correct any leaks. See the

Leaks

section at the

beginning of this chapter.

Saturated methane/isobutane gas purifier

Replace the gas purifier.

Poor quality methane (purity below 99.99%)

Replace the methane with high-purity methane. If necessary, clean and purge
the reagent gas lines and clean the ion source.

Reagent gas flows too high (in EI/PCI MSDs)

Verify that the reagent gas setup is correct.

Summary of Contents for 5977B Series



































































































































































































































































Search results

Summary of Contents for 5977B Series

Reviews:

Brands by name

Popular brands

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Search results

Summary of Contents for 5977B Series

Reviews:

Brands by name

Popular brands