manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 57

General Troubleshooting

2

5977B Series MSD Troubleshooting and Maintenance Manual

57

•

HED power supply output cable failed

•

Electrical leads to the ion source are not connected correctly

•

Filament shorted to the source body

Temperature control disabled

•

One of the heater fuses has failed

•

MSD electronics are not working correctly

Temperature control fault

This indicates that something has gone wrong with the temperature control of 
either the ion source or mass filter (quad) heater. The cause can be further 
isolated by selecting 

mp Status/MS TeCtlr Status

 in the Tune and Vacuum 

Control view. One of the following should be displayed as the cause:

•

Source temperature sensor is open

•

Source temperature sensor is shorted

•

Mass filter (quad) temperature sensor is open

•

Mass filter (quad) temperature sensor is shorted

•

No heater voltage (heater fuse has probably failed)

•

Heater voltage is too low

•

Temperature zone has timed out (heater failed, bad heater wiring, or loose 
temperature sensor)

•

Problem with the temperature control electronics

•

Source heater is open

•

Source heater is shorted

•

Mass filter heater is open

•

Mass filter heater is shorted

The high vacuum pump is not ready

•

Turbo pump is on but has not had enough time (5 minutes) to reach 80% of 
its normal operating speed

•

Turbo pump is not working correctly

•

MSD electronics are not working correctly

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands