manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 132

132

5977B Series MSD Troubleshooting and Maintenance Manual

4

General Maintenance

To Install the EI Calibration and Vent Valve Assembly

Materials needed

•

Calibration valve

•

Diffusion (G7077-60211)

•

Turbo (G7077-60204)

•

O-ring for calibration valve (0905-1217)

•

PFTBA (05971-60571) or other tuning compound

•

Screwdriver, Torx T-20 (8710-1615)

Procedure

1

Remove the old valve assembly. (See

 “To Remove the EI Calibration and 

Vent Valve Assembly” 

on page 131 and 

Figure 18

 on page 128.)

2

Ensure the valve O-ring is in place. If it is worn or damaged, replace it.

3

Install the calibration and vent valve assembly, and tighten the screws that 
hold it in place. 

4

Reconnect the calibration valve cable to the connector next to the fan.

5

Remove the vial from the new calibration valve. (See

 “To Refill the EI 

Calibration Vial” 

on page 128.) The valve is supplied with a vial already 

installed.

6

Fill and reinstall the calibration vial. 

7

Pump down the MSD. 

    

             

C A U T I O N

Failure to purge the calibration valve will damage the filaments and detector.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands