manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 182

182

5977B Series MSD Troubleshooting and Maintenance Manual

7

Analyzer

Overview

The analyzer with an XTR source (See 

Figure 39

 on page 184)or the analyzer 

with a HES (See 

Figure 44

 on page 193) is the heart of the MSD. It ionizes the 

sample, filters the ions, and detects them. The sample components exiting the 
GC column flow into the ion source. In the ion source, the sample molecules 
are ionized and fragmented. The resulting ions are repelled from the ion 
source into the quadrupole mass filter. The mass filter allows selected ions to 
pass through the filter and strike the detector. The detector generates a signal 
current proportional to the number of ions striking it.

The analyzer is attached to the vacuum side of the side plate. The side plate is 
hinged for easy access. The ion source and the mass filter are independently 
heated. Each is mounted inside a radiator for correct heat distribution. 

Each of the parts of the analyzer is discussed in the following material.

The analyzer has four basic components

The analyzer consists of the following components (See 

Figure 39

 on page 184) 

or (See 

Figure 38

 on page 183):

•

Ion source

•

Mass filter

•

Detector

•

Heaters and radiators

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands