manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 25

Introduction

1

5977B Series MSD Troubleshooting and Maintenance Manual

25

Precautions

Take the following precautions when operating a GC/MSD system with 
hydrogen carrier gas.

Equipment precaution

You MUST ensure the front side-plate thumbscrew is fastened finger-tight. Do 
not overtighten the thumbscrew; it can cause air leaks.

You must remove the analyzer window cover on the front of a 5977B HES MSD. 
In the unlikely event of an explosion, this cover may dislodge.

Power failure 

If the power fails, both the GC and mass 
spectrometer shut down. The carrier gas, however, 
is not necessarily shut down. As described 
previously, in some GCs a power failure may cause 
the carrier gas flow to be set to maximum. As a 
result, hydrogen may accumulate in the mass 
spectrometer.

Table 4  

Hydrogen accumulation mechanisms (continued)

Mechanism

Results

WA R N I N G

Once hydrogen has accumulated in a mass spectrometer, extreme caution must be 
used when removing it. Incorrect startup of a mass spectrometer filled with 
hydrogen can cause an explosion.

WA R N I N G

After a power failure, the mass spectrometer may start up and begin the pumpdown 
process by itself. This does not guarantee that all hydrogen has been removed from 
the system, or that the explosion hazard has been removed.

WA R N I N G

Failure to secure your MSD as described above greatly increases the chance of 
personal injury in the event of an explosion.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands