manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 217

Electronics

8

5977B Series MSD Troubleshooting and Maintenance Manual

217

•

Turns off the diffusion pump if the foreline pressure is too high or if the 
diffusion pump is too hot.

•

Passes the foreline pressure signal from the foreline gauge or turbo pump 
speed and other vacuum status information to the main board.

•

Turns off the foreline pump in case of a problem with pumpdown.

Diffusion pump control

The power regulator ensures that the diffusion pump heater receives constant 
power, even if there are fluctuations in the AC line voltage. It measures the 
voltage across the heater and the current through it, multiplies them together, 
and compares the result with a standard value. Any discrepancy is applied as 
an error signal to adjust the power.

If the power distribution board senses a malfunction in the diffusion pump 
power regulator, it shuts off power to the diffusion pump. See 

Figure 52

.

Turbo pump control

Your MSD is equipped with a turbo pump with an integrated controller.

Figure 52  

Diffusion pump control

Hi vac power cable

Diffusion pump 
harness

Diffusion pump 
heater cable

Fan

Diffusion 

pump

Heater

Sensors

HI VAC Power

Harness

CAL 

valve

MSD electronics module 

(AC board)

Fore-

line

gauge

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands