manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 64

64

3

CI Troubleshooting

Common CI-Specific Problems

Because of the added complexity of the parts required for CI, there are many 
potential problems added. The greatest number of, and most serious problems 
with CI are associated with leaks or contamination in the reagent gas 
introduction system. NCI is especially sensitive to the presence of air; small 
leaks that cause no problems in PCI can destroy NCI sensitivity.

As with EI, if the MSD tunes well and no air leak is present, sample sensitivity 
problems should be addressed by GC inlet maintenance first.

•

Wrong reagent gas

•

Reagent gas not hooked up or hooked up to wrong reagent gas inlet port

•

Wrong ions entered in tune file

•

Wrong tune file selected

•

Not enough bakeout time has elapsed since vent (background is too high)

•

Wrong column positioning (extending > 2 mm past tip of interface)

•

Interface tip seal not installed

•

EI ion source installed in CI mode

•

EI filament or other EI ion source parts in CI ion source

•

Air leaks in reagent gas flow path

•

CI filament has stretched and sagged:

•

High EMV

•

Linear (no inflection point) electron energy (EIEnrgy) ramp

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands