manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 77

CI Troubleshooting

3

77

No or low reagent gas signal

If you have just installed the CI ion source and have an air leak or large amounts 
of water in the system after running one or more autotunes, the ion source is 
probably dirty.

Fix the air leak. Clean the ion source, and bake out for 2 hours before tuning. 
See the 

Operation Manual

.

The wrong reagent gas is flowing.

Turn on the correct reagent gas for your tune file.

Ion polarity is set to Negative. No reagent gas ions are formed in NCI.

Switch to Positive ionization mode.

The reagent gas flow is set too low.

Increase the reagent gas flow.

Reagent gas supply tubing is blocked, kinked, pinched, or disconnected.

Inspect and, if necessary, repair or replace the reagent gas supply tubing.

Wrong filament wires are connected to filament.

Ensure that the filament 1 wires are connected to the CI ion source filament, 
and that the filament 2 wires are connected to the dummy filament.

Carbon has built up on the filament, or the filament has sagged out of alignment.

Inspect the filament, if necessary, replace the filament.

Too much air or water in the system.

Run the methane pretune. Peaks at 

m/z

 32 and 19 usually indicate air and 

water, respectively. Bake out and purge the instrument until there is no visible 
peak at 

m/z

 32, and the peak at 

m/z

 19 is reduced to a very low level. If the 

peak at 

m/z

 32 does not decrease, an air leak is likely. See

 “Air Leaks” 

on 

page 66 for more information. 

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands