manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 27

Introduction

1

5977B Series MSD Troubleshooting and Maintenance Manual

27

Safety and Regulatory Certifications

The 5977B HES Series MSD conforms to the following safety standards:

•

Canadian Standards Association (CSA): CAN/CSA-C222 No. 61010-1-04

•

CSA/Nationally Recognized Test Laboratory (NRTL): UL 61010–1

•

International Electrotechnical Commission (IEC): 61010–1

•

EuroNorm (EN): 61010–1

The 5977B HES Series MSD conforms to the following regulations on 
Electromagnetic Compatibility (EMC) and Radio Frequency Interference 
(RFI):

•

CISPR 11/EN 55011: Group 1, Class A

•

IEC/EN 61326

•

AUS/NZ 

This ISM device complies with Canadian ICES-001. Cet appareil ISM est 
conforme a la norme NMB—001 du Canada. 

The 5977B Series MSD is designed and manufactured under a quality system 
registered to ISO 9001.

The 5977B HES Series MSD is RoHS compliant.

Information

The 5977B Series MSD meets the following IEC (International 
Electro-technical Commission) classifications: Equipment Class I, Laboratory 
Equipment, Installation Category II, Pollution Degree 2.

This unit has been designed and tested in accordance with recognized safety 
standards, and is designed for use indoors. If the instrument is used in a 
manner not specified by the manufacturer, the protection provided by the 
instrument may be impaired. Whenever the safety protection of the MSD has 
been compromised, disconnect the unit from all power sources, and secure the 
unit against unintended operation.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands